php What should I do if the pins of the Yuzai motherboard are accidentally bent? This is a common problem, but it can cause headaches. Bends on your motherboard's pins may prevent your device from working properly, but don't worry, there are some solutions. First of all, don't panic and stay calm. Second, try using a small tool, such as pliers or a tiny screwdriver, to gently repair the bent pins. If this method doesn't work, consider sending the motherboard to a professional electronics repair shop for repair. In short, do not disassemble or assemble the motherboard yourself when encountering this situation to avoid causing greater damage.
The pins of the CPU socket on the computer motherboard were accidentally bent, but they are still usable. Many pin corners of the CPU are shielded and useless, so they are not needed when connecting to the motherboard. However, after the motherboard pins are bent, you can use tweezers to gently adjust the pins back to their normal shape.
If there is no problem in actual use like this, don't worry about it. If there is a problem, cut a piece of thin copper wire that is as thick as the corner of the CPU pin and slightly longer.
Just use the copper wire in the network cable. Of course, other materials with suitable thickness and hardness can also be used.
Insert it into the cpu card holder first, and then put the cpu. Adjust the length just enough to be in contact with the broken corner point of the CPU, not too long or too short. There is no warranty in this case. Because it was trauma.
1. If the jumper or pin on the motherboard is bent, use tweezers to straighten it.
2. If the pins of the CPU base on the motherboard are bent, you have to be careful. The pins in the lower right corner are bent.
3. At this time, you need to use a thin Hold the warped pin with tweezers and carefully press it in the original direction. If it doesn't work, try again. This is the correction effect, which is no different from the original one.
Whether the motherboard CPU base pins are bent will affect booting requires detailed analysis of the specific situation. If the number of bent pins is small and the degree of bending is not serious, generally speaking, it will not affect booting. However, if there are a large number of bent pins, or the degree of bending is severe, it may result in the inability to connect the CPU and the motherboard properly, thus affecting the normal startup of the computer. In addition, even if it can be started normally, some strange phenomena may occur, such as the computer running slowly and crashing frequently. Because this may be caused by obstacles in the communication between the CPU and the motherboard, and data transmission is blocked. Therefore, if you find that the motherboard CPU base pins are bent, it is recommended to use tools to correct them as soon as possible. After adjustment, if it can start normally, then the problem will not be caused by the pins.
The motherboard has no pins, but the CPU pins are crooked. The solution to the problem of bent CPU pins is: First, confirm the degree of damage to the CPU pins. If it is just bent, it can be easily solved. You only need to take some sharp objects, such as cards and blades, to cut the CPU pins. Straighten the pins. But don’t use too much force. Don’t continue to use force if you feel that you can’t use force. Check the effect first. Sometimes you may feel that you haven’t used force, but in fact you have broken the pin straight or bent it in the opposite direction, so be careful. Be cautious and avoid breaking.
In most cases, once it breaks, you can only go to a third-party outlet for repair. If you feel that you are very capable, you can try to solder it with a soldering iron or a hot air gun, but the risk is extremely high. If it is not high-end, You can try it yourself and learn from experience. If it is a high-end processor, it is safer to find professionals to handle it.
In daily use, AMD's pins are actually relatively stable, but some application scenarios can cause damage to users. I will introduce them to you here.
First of all, when installing the CPU, yes, when loading the CPU into the lid, because AMD's lid actually has two sides, and the CPU can be installed on both sides. But if you install it backwards, the pins of this processor will inevitably bend, so be careful. As for why the author is so sure, of course I have learned a lot of lessons.
In addition to the easy damage to the pins when installing the CPU, the other is when replacing the processor. Many users sometimes take off the CPU and the heater directly when disassembling the CPU radiator. It may be that too much silicone grease is applied, causing the CPU top cover to fit tightly with the radiator. At this time, it is possible to cause damage to the CPU. This red phenomenon is much more serious than installing it backwards in the cover, because at most the pins will be bent when installed backwards, but removing the CPOU heat dissipation together may directly cause the CPU pins to break.
If you accidentally remove the CPU like this, you can use a sharp object to knock the CPU off the side gap bit by bit, or use a hot hair dryer to blow out the silicone grease. Just be careful not to use too much force to cause miracles. All easy to say.
To avoid this situation, there are generally two methods. First, before removing the CPU, turn on the computer copy machine to let the silicone grease melt away, so that it will no longer be sticky. The second is to use the AMD anti-pull-out bracket produced by a third party during installation, which can also avoid this phenomenon.
1. First of all, when the CPU pins are twisted or bent, try to protect the CPU to avoid a similar situation happening again.
2. Secondly, you need to find a very flat place, such as a desk, which will help the CPU recover.
3. Next, you need such an artifact, which is an injection needle. Polish the tip of the injection needle smoothly.
4. Then, use the needle hole of the injection needle to insert the CPU pin position that needs to be straightened, and straighten the pin.
5. Finally, everyone needs to pay attention to the fact that the force should be light and try to follow the trend, so as not to cause the stitches to break. The pins of the CPU socket on the computer motherboard were accidentally bent, but they are still usable. Many pin corners of the CPU are shielded and useless, so they are not needed when connecting to the motherboard. However, after the motherboard pins are bent, you can use tweezers to gently adjust the pins back to their normal shape. If there is no problem in actual use like this, don't worry about it.
Just say a few points that you must pay attention to.
1. Pay attention to the contacts of the CPU. The CPU does not like to break, but it does not mean that it will not break. Handle it with care. If the motherboard is not flat after putting it on, do not push down the buckle of the motherboard. Some CPUs have a card slot that matches the motherboard. Put it in gently without force.
2. Motherboards, especially Intel motherboards, because the pins are on the motherboard, and the pins are very, very easy to bend. If they are bent, it is basically difficult to bend them, so be sure not to bend the motherboard. If the needle is bent, send it back for warranty as soon as possible or ask JD.com to pick it up.
3. The gold finger of the graphics card is not easy to break, but it does not mean that it will not break. After plugging it in, if you want to pull it out, please press the buckle first. Do not remove the screw and pull it out directly. , either the motherboard GG or your graphics card GG. Everyone buys things like graphics cards on the go. The warranty is not that quick and fast, so be careful.
4. Generally speaking, the problem of not turning on the machine is partly due to the memory. Pay attention to whether the memory is compatible. Pay attention to whether the golden part of the memory is dirty or oxidized. If there is more memory, please note that if you want to enable multi-channel, separate the Inserted.
5. Don’t be greedy for petty bargains and buy cheap ones on some hardware, such as the motherboard. After the arrival, the memory slot is broken. What can I say? Another example is the power supply. The last maximum peak value is 400W. Okay. If you don’t know the rated power, it’s BOOM. Who should you call?
6. You don’t need to apply too much silicone grease. The purpose of silicone grease is to conduct heat. If there is too much, it is not good. Just put it on the CPU and then cover the cooling head or radiator. Yes, it doesn’t matter if you squeeze them into a pile, it’s completely fine to use the cooling head to flatten them yourself.
7. Don’t close the case cover so early. If there is a problem, check the indicator light first. There is no need to unplug all hardware.
8. Be careful not to pile up the wires inside the chassis. The first thing to do when installing the power supply is to remove the back wires and leave room for them. It's really, really hard to clean up.
Think of adding more~
Will the motherboard pins be bent a little and affect the use?
Motherboard pins What does "bent" mean? Is it serious?
If the motherboard pins are bent, it may cause the following problems:
System instability: The motherboard pins are bent, which may cause system instability, crashes, blue screens, restarts and other problems.
Performance degradation: If the motherboard pins are severely bent, it may cause system performance degradation, such as slower computer operation, slower response speed, etc.
Hardware failure: Bending the motherboard pins may cause hardware failure, such as failure to recognize certain devices, failure of the device to work properly, etc.
Therefore, if you find that the motherboard pins are bent, you should take timely measures to repair or replace them. It is recommended to seek help from professional technicians for repair or replacement to ensure that the system can work normally and stably.
The above is the detailed content of What should I do if the motherboard pins are bent?. For more information, please follow other related articles on the PHP Chinese website!
![[Web front-end] Node.js quick start](https://img.php.cn/upload/course/000/000/067/662b5d34ba7c0227.png)
