What is the problem when the red light of wifi los keeps flashing?

The los red light of wifi keeps flashing, which means that the network signal or connection has been lost, which means that the router device has not received the light signal, so it is impossible to access the Internet when connected to Wi-Fi. Reasons for the flashing red light of los: 1. The connection port of the indoor pigtail connection device is somewhat loose; 2. The connection port of the indoor pigtail connection device may have poor contact; 3. The optical fiber cable is bent too much or the surface is damaged; 4. , the router is damaged or there is a problem with the external line.

The operating environment of this tutorial: Windows 7 system, Dell G3 computer.

What is the LOS light for?

Due to the rapid development of the times, most of my friends have now enjoyed the convenience brought by 4G network, and 5G high-speed network will soon come. Whether at home or in a street coffee shop, we can connect to Wi-Fi to surf the Internet, which can also save a lot of traffic costs. But sometimes, why does the los light on our Wi-Fi keep flashing red?

LOS is an indicator light on the Wi-Fi signal or optical modem router all-in-one device, used to indicate that the network signal or connection has been lost. The optical modem or router has no network due to signal loss.

When the network signal is lost, different optical modems or routers will provide different instructions. But usually the LOS red light flashes or stays on.

When the LOS light is off, it is in a normal state, which means that the router device has received the optical signal; when the LOS light is flashing red, it is in an abnormal state, which means that the router device has not received the optical signal. , so we can’t access the Internet even when connected to Wi-Fi.

The reason why the red light of wifi los keeps flashing

The first situation:

possible The connection port of the indoor pigtail connection device is somewhat loose. Try unplugging the connector and plugging it in again;

Second case:

Indoor pigtail The connection port of the connected device may have some poor contact. We first unplug the connection port, wipe it clean with a napkin and then re-insert it;

The third situation:

Some optical fiber cables at home are bent too much or have surface damage. This situation will affect the total reflection transmission of light signals in the optical fiber. Check whether there is damage on the outside of the optical fiber cable and straighten the optical fiber;

The fourth situation:

The router is damaged or there is a problem with the external line.

If the above adjustments are ineffective, we need to report a fault and contact the staff of the broadband communication company to describe the situation we encountered and ask professionals to come to repair the Wi-Fi router and fiber optic broadband. Can.

Extended information:

Common router faults and solutions:

1. Internet speed slows down

After using a broadband router, the Internet speed will decrease, which is not actually a fault. Sharing the Internet through a broadband router will cause a certain loss of Internet speed, which is inevitable. However, this loss can be minimized by changing the MTU value of your router.

2. Unable to dial up

Connected to the broadband router and unable to dial up. According to this phenomenon, there should be no problem with the hardware of the product you just purchased. Most problems lie in the router's software settings. You can find the product manual of the router, enter the configuration interface according to its default IP address, and then dial after configuration.

3. Frequent disconnections

Using a broadband router to share the Internet often disconnects, and the connection to the network can only be disconnected periodically, which indicates that the problem still lies with the broadband router itself. , such as stability and settings.

4. Unable to log in

Cannot log in to the broadband router settings page. If you have successfully entered the setting interface before, please first check the hardware connection between the broadband router and the computer, and set the network card to "obtain an IP address automatically", otherwise the local address must be set to the broadband router. In the same network segment, please set the gateway address as the default IP address of the router.

For more related knowledge, please visit theFAQcolumn!

The above is the detailed content of What is the problem when the red light of wifi los keeps flashing?. For more information, please follow other related articles on the PHP Chinese website!