How to install a hard drive on a desktop computer

How to install a hard drive on a computer

1. First open the hard drive package you purchased. Take the installation of a solid-state drive and a mechanical hard drive as an example. When buying a mechanical hard drive, it usually comes with a mechanical hard drive. One hard drive, one SATA interface cable, and four screws. There are two SATA interfaces above the hard disk, one is a large interface and the other is a small interface.

2. The M.2 installation method for desktop computers and laptops is the same. Laptops need to be disassembled. Here we mainly take desktop computers as an example. First, you need to find the M.2 slot of the motherboard and remove the copper studs. Screw it to the third hole "2280 specification". Most M.2 solid-state drives are 2280 mainstream specifications.

3. Before installing dual hard drives, you must first check the basic conditions inside the computer, such as whether there is space for installing a second hard drive, whether there are free interfaces for the data cable, and whether the computer power supply can support two hard drives. stable operation, etc. These conditions are very important for installing dual hard drives.

4. The computer hard drive installation method is as follows: Tools: screwdriver, hard drive, chassis, screws. First, lay the case flat so that it is easier to install the hard drive. Then gently push the hard drive (the side with the logo, when the case is placed correctly, toward the chassis, and the end with the interface facing the motherboard) into the hard drive slot from right to left.

5. The hardware installation of dual hard drives is completed. CMOS setting parameters: After installing the hard disk, start the computer and hold down the "Delete" key to enter the CMOS setting interface. At this time, select "IDE HDD Auto Detection" and press Enter to check whether the two hard drives are normal.

6. Taking the installation of a mechanical hard drive on a desktop computer as an example, the operation process is as follows: Prepare the mechanical hard drive, data cables and screws. There will be two interfaces above the hard disk. The large interface is for connecting the power supply, and the small interface is for connecting the motherboard and the hard disk.

I want to add a solid-state drive to my computer, how to install it?

Before installing the solid-state drive, first take out all the things shipped with the solid-state drive; the most important thing is the solid-state drive Main body, solid state drive mounting bracket and screws, and data cable.

First of all, we need to prepare an M.2 solid-state drive and installation tools (screwdriver is enough), and open the side panel of the computer host chassis. Find the M.2 interface location on the motherboard, and use a screwdriver to remove the screws from the M.2 slot on the motherboard.

Shut down the computer and unplug the power cord. Open the computer case, find a free 5-inch or 5-inch hard drive bay, and install the SSD in it. If you need to install the SSD in a 5-inch hard drive bay, you need to use an adapter bracket to fix it to the 5-inch hard drive bay. Connect the new SSD to the motherboard using a SATA cable.

The internal structure of solid state drive. Insert the solid state drive into the optical drive box. Remove the screw from the optical drive location. Use a screwdriver to push the metal piece down and the optical drive pops out. Place the optical drive box containing the solid state drive into the optical drive bay of the notebook. Remove the optical drive bezel. Install the bezel on the optical drive position.

How to install a desktop computer hard drive

After opening the purchased hard drive, it will usually come with a SATA data cable; open your chassis cover. First, connect the data cables from the motherboard SATA interface to the hard disk SATA interface, and connect the power cable. The flat end is connected to the hard drive, and the large end is connected to the power supply.

After the hard disk is installed on the computer, turn on the computer, right-click "My Computer" on the desktop and click "Manage". Click "Disk Management" and click: "OK" to initialize. Remember the serial number of disk 0, select disk 0, right-click the mouse, and click "New Simple Volume". Click "Next".

First disassemble the hard drive. This is a 256G solid state drive, which is quite small. Then disassemble the computer.

Press DEL when booting (press this key on most computers, please refer to the motherboard manual), enter the CMOS settings, enter the first option, and find the master disk you want to set just now (Master is the main disk and Slave is the slave disk) ), select and exit, save and restart the computer. Question 3: How to add a hard drive to a desktop computer (detailed steps) Of course, you can add it.

Question 5: Step-by-step diagram of how to install a computer hard drive (1) A desktop computer can install two hard drives.

Desktop computers need to install two hard drives and how to set them up: Open the computer case, unscrew the screws on the back of the case, and remove the protective plate, as shown in the picture: Find the place where the hard drive is installed, and connect the data cable OK, just install it.

Desktop computers need to install two hard drives. How to install them? How to set the primary and secondary hard drives?

IDE hard drives use jumpers to distinguish the primary and secondary hard drives. The specific setting method is slightly different for hard drives produced by different manufacturers. Please check the instructions on the hard drive for details. The master-slave setting of SATA hard disk does not require setting jumpers, it is mainly determined by the data cable interface on the computer motherboard.

Directly connect the two serial data cables to the seven-shaped sockets of the two hard disks, and then use the flat sockets of the power supply to plug into the two SATA hard disks respectively.

We need to connect one of the two IDE interface settings to the optical drive and the other to the hard disk. Because there is only one IDE interface for connecting the hard disk at this time, we have to connect two hard disks to one hard disk data line.

How to install a solid-state drive on a desktop computer

The method of installing a solid-state drive on a desktop computer is as follows: Prepare a SATA to USB cable, a data cable, a hard drive bracket and other necessary Tools such as screwdrivers and screws. Use the SATA to USB data cable to connect the connector to the desktop computer.

Remove the side panel of the chassis to expose the motherboard inside the host. Prepare the SSD hard drive and SATA connection cable. Connect one end of the SATA cable to the SATA interface on the motherboard. Connect the other end of the SATA cable to the transmission interface of the SSD. Locate the SATA hard drive power supply wiring from the wiring leading out of the computer power supply.

Prepare installation tools, including: 1 SATA to USB adapter cable, 1 SATA data cable, and 1 hard drive bracket. Install the system migration software to migrate the existing system and data to the new SSD hard drive. Connect to desktop computer using SATA to USB connector. Migration of system data.

The specific steps are as follows: Prepare the solid state drive and screwdriver. Open the chassis cover and identify the location of the hard drive and optical drive. The connecting cable on the mechanical hard drive is what we need to connect to the solid state drive; remove the cable.

How to install a mechanical hard drive on a desktop computer

1. First, you need to prepare three things, and one of them is indispensable. The first is the hard drive, and the second is the SATA cable. Pay attention to asking clearly when buying the hard drive. Check to see if it is equipped with a SATA cable. If not, you need to buy it separately. The third is the power cable. Some hosts come with a power cable. If not, you need to buy it separately.

2. There was already a system in the past. Now, if you add a hard disk, you don’t need to redo the system. You only need to connect the hard disk. If it is an IDE hard disk, you need to pay attention to the settings of the master and slave disks. If it is a SATA hard disk, you need to pay attention to the startup sequence.

3. Connect the solid state to the computer at the same time and set up the master-slave hard drive relationship (the solid state waits for one hard drive). The solid state and the mechanical drive can be used together. Most desktop computers are used in this way.

4. Question 6: The computer system is in a solid-state drive. How to add a mechanical hard drive? It can be added to any interface. Just select the default hard drive as the solid-state drive in the startup settings. Question 7: How to add an extra hard drive to the computer. Desktop computers can add an extra hard drive, but most laptops cannot.

5. If two hard disks are connected to the same hard disk data line, the second hard disk should be set as the slave disk SL (Slave Device).

The above is the detailed content of How to install a hard drive on a desktop computer. For more information, please follow other related articles on the PHP Chinese website!