Win10 prompt: The system failed to start normally

Win10 cannot boot and displays: Your computer did not start correctly

Win10 cannot boot and displays: Your computer did not start correctly

Upgrading from win7 to win10 shows that the computer did not start correctly. Solution:

1. MBR failure.

Fault manifestation: An error message similar to "press F11 start to system restore" appears after booting.

Cause analysis: In order to achieve the purpose of priority startup, many software such as One-click Ghost often modify the hard disk MBR during installation, so that the corresponding boot menu information will appear when booting. However, if such software is defective or incompatible with Win7, it is very easy for Win7 to fail to start normally.

Solution: For the repair operation of the hard disk master boot record (MBR), use the repair tool included in the Win7 installation CD: Bootrec.exe to solve this fault.

The specific steps are: first start the computer with the Win7 installation CD. After the CD boot is completed, press the Shift F10 key to bring up the command prompt window and enter the DOS command "bootrec /fixboot", then press the Enter key and follow the prompts to complete the rewriting of the hard disk master boot record.

2. Oxc000000e fault.

Fault manifestation: You cannot log in to the system normally when booting, but the Oxc000000e fault prompt pops up directly.

Cause analysis: Due to the installation or uninstallation of some special software, it will cause very serious damage to the boot program of Win7, so that the Oxc000000e error will appear when Win7 starts and the system cannot start normally. In this case, even pressing the F8 shortcut key cannot bring up the advanced startup menu of Win7, and the repair operation cannot be performed in safe mode.

Solution: After pressing Shift F10 to bring up the command prompt, execute the following five DOS commands in sequence (C drive is the system disk installed by Win7. It needs to be modified according to the actual situation of the computer. It is C. Press Enter after each command. End, the running results automatically appear below the command, the same below):

C:

cd windows\system32.

bcdedit /set {default} osdevice boot.

bcdedit /set {default} device boot.

bcdedit /set {default} detecthal 1.

3. BOOTMGR ismissing error occurs when booting.

Fault manifestation: Whenever the computer is turned on, an error message will appear, and the system cannot be logged in normally. This error message, translated into Chinese, means that Bootmgr is missing. Press Ctrl Alt Del to restart.

Cause analysis: The reason for this startup failure may be that the Bootmgr file is indeed lost, or it is caused by a disk error.

Solution: If the Bootmgr file is lost, you can solve the problem by rebuilding the Win7 boot file.

The operation steps are: execute the following two DOS commands in sequence at the cursor position of the window (C is the system drive letter):

C:

bcdboot C:\windows /s C:

Then restart the system, you can see the familiar boot menu of Win7, and then select the first Win7 menu option. After some initialization operations, you can use the Win7 system normally.

Completely decompress the files on the C drive and then restart the system to log in to the Win7 system normally.

What to do if the computer sometimes fails to start

Use the COPY CON command to create a Boot.ini file. Type Copy Con C:\boot.ini under DOS and press Enter. Then follow Boot, but there is no hal.dll file on other paths, causing this error to be prompted when booting from C:\Windows by default. The general solution is to enter the recovery console and use the fixboot command. The .ini file is illegal. The system will prompt 1 file(s) copied.

4), if boot.ini cannot be repaired in this way, use bootcfg/add to rebuild boot, copy the file back to system32: Keep trying, and when you see the USB disk, just use

copy hal, it can be said that the reason for this error is that there is an error in the boot.ini file, which prevents the machine from being booted from the specified path.

3), use the EDIT.EXE command to edit this file. Start EDIT and save it as Boot.DLL file.

There is another way, you use a USB flash drive to copy a hal.dll file from someone else, then insert it into your computer, and then use a system installation disk to put into the CD-ROM drive. In the first choice, enter the format of the .ini file. Press the Enter key once for each line. When all the content is entered, press CTRL Z and you will see the ^Z prompt on the screen. At this time, hit Enter again.

2). Then from a: b. The startup therefore fails. The solution is to re-edit the Boot.ini file.

1). After using the Win9X startup disk to start the .EXE, as long as you enter the contents of the Boot.ini file in the correct format, it cannot be solved at all. This means that the creation is successful. Select repair and you can enter the doc. .ini.dll c. After creating it on another computer, it prompts that hal.dll is damaged or missing. Use the bootcfg command in the recovery console; hal.dll is fine,

The principle is that when installing the system, but because your Windows XP is not installed on the C drive, the system prompts that the HAL cannot be found, so the system searches for other paths. In fact, the file does not necessarily exist. Copy Just go to the root directory of the damaged computer's C drive and overwrite the source files.

This is due to the boot:\windows\system32\.ini file in the root directory of drive C

What to do if the computer cannot start

1.CMOS battery failed

中文：CMOS battery failure.

Explanation: This means that the CMOS battery is almost out of power, just replace it with a new one.

2.CMOS check sum error-Defaults loaded

Chinese: An error was found when CMOS performed all checks and the system default values must be loaded.

Explanation: Generally speaking, this sentence means that the battery is almost out of power. You can try changing the battery first. If the problem is still not solved, it means that there may be a problem with the CMOS RAM. If it is less than a year old, go to the dealer. Replace the motherboard at the dealer, and after a year have the dealer send it back to the manufacturer for repair!

3.Press ESC to skip memory test

Chinese: Memory check is in progress, you can press ESC key to skip.

Explanation: This is because there is no setting in CMOS to skip the second, third, and fourth tests of the memory. Four memory tests will be performed when the computer is turned on. Of course, you can also press the ESC key to end the memory check, but each time It's too troublesome to do this. You can enter COMS settings and select BIOS FEATURS SETUP, set Quick Power On Self Test to Enabled, save and restart.

4.Keyboard error or no keyboard present

Chinese: Keyboard error or missing keyboard.

Explanation: Check whether the keyboard connection is loose or damaged.

5.Hard disk install failure

中文：Hard disk installation failed.

Explanation: This is because the power cable or data cable of the hard disk may not be connected properly or the hard disk jumper may not be set properly. You can check whether the hard disk connections are plugged in properly and see if the jumper settings of the two hard disks on the same data line are the same. If they are the same, just set the jumper settings of the two hard disks differently. (One is set as Master and the other is set as Slave).

6.Secondary slave hard fail

Chinese: Failed to detect slave disk

Explanation: It may be that the CMOS settings are improper. For example, if there is no slave disk but it is set to have a slave disk in CMOS, an error will occur. In this case, you can enter the COMS settings and select IDE HDD AUTO DETECTION for automatic hard disk detection. It is also possible that the power cable and data cable of the hard disk may not be connected properly or the hard disk jumper is set improperly. For the solution, refer to item 5.

7.Floppy Disk(s) fail or Floppy Disk(s) fail(80) or Floppy Disk(s) fail(40)

中文: The floppy drive cannot be driven.

Explanation: The system prompts that the floppy drive cannot be found. Check whether the power cord and data cable of the floppy drive are loose or connected incorrectly, or try putting the floppy drive on another machine. If none of these work, then I had to buy another one, but fortunately the floppy drive was not expensive.

8.Hard disk(s) diagnosis fail

中文: An error occurred while performing hard drive diagnostics.

Explanation: This problem generally means that the hard disk itself is faulty. You can put the hard disk on another machine and try it. If the problem is still not solved, you can only repair it.

9.Memory test fail

Chinese: Memory check failed.

Explanation: Re-insert and unplug the memory stick to see if it can be solved. This problem is usually because the memory sticks are incompatible with each other. Go and replace it!

10.Override enable-Defaults loaded

Chinese: The current CMOS settings cannot boot the system. Load the default values in the BIOS to boot the system.

Explanation: Usually there is an error in the settings in COMS. Just enter the COMS settings and select LOAD SETUP DEFAULTS to load the original system settings and then restart.

After a problem occurs during the power-on self-test, various English phrases will appear. The phrases contain very important information. By understanding this information, you can solve some minor problems by yourself. However, these English sentences stump some friends. , the following are explanations of some common BIOS phrases, you can refer to them.

The above is the detailed content of Win10 prompt: The system failed to start normally. For more information, please follow other related articles on the PHP Chinese website!