How to use Unetbootin to write the Linux system to a USB flash drive and perform boot settings

Linux There are many different versions of Linux, but they all use the Linux kernel. So do you know the solution to install the Linux system on the USB flash drive? Next is the solution to the installation of the Linux system on the USB flash drive collected by the editor for you. You are welcome to read:

Solution to install Linux system on U disk

Planning to work:

|Unetbootin: Linux system writing U disk tool.

|BOOTICE: Boot setup tool.

|Your own Linux system ISO image.

|Format the USB flash drive into FAT32 format, right-click on the USB flash drive - low format, no tools are required.

The first step is kali linux, use unetbootin to write the Linux system ISO image to the USB flash drive.

Double-click to start UnetbootinU disk boot installation linuxLinux environment configuration, you will see the following interface.

Click OK after selecting. The following interface appears and it takes about 30 seconds to complete.

After completing the above steps, the Linux system will be written to the USB flash drive.

Why do you need to use Unetbootin to write? Does UltraISO not work? The reason is that just writing the system to the USB disk will not start, and you need to use syslinux to boot. syslinux is actually a very small Linux system that only plays a booting role. . Unetbootin comes with syslinux, as you can see from the picture above, which eliminates the complexity of automatic installation. UltraISO does not have this function.

The second step is to use BOOTICE to set up the USB drive to boot.

Start BOOTICE. Choose a USB flash drive, never a hard drive. . . . Then click "Master Boot Record".

Configure the main boot as UltraISOUSB-ZIP+ in the pop-up interface.

After setting up, close this interface, return to the main interface and click "Partition Boot Record".

Check whether the partition boot record is syslinux. If not, configure it to syslinux. Usually this step is fine. Just to be on the safe side it's better to take a look. . . .

Go back to the main interface again and click "Partition Management".

Check whether the U disk is set as an active partition. The one marked with A is the active partition. If not, just click "Activate". If it is not set as an active partition, "StartfromUSB..." will pop up endlessly when the notebook is started from the USB flash drive

At this point, the USB flash drive can be successfully started.

Plug in the USB flash drive and set the notebook to boot from USB.

In addition, if the startup fails because the Linux system driver is not supported, there is no solution yet and you can only change the system.

Since this article is called the solution U disk boot installation linux, let me talk a little more and introduce another solution.

Introduction:

There is a popular China Unicom Linux operating system puppy abroad. It supports English and has a beautiful interface. It also supports multimedia very well, such as QQ and watching videos. What's more, the compatibility is very strong.

Making tools:

Creating a USB bootable disk is very simple, you only need the following two tools.

PuppyLiveUSB: A tool for writing the Puppy system ISO image to a USB flash drive with one click. This tool can only be written to the Puppy system. For ordinary systems, use the method mentioned above.

custom-puppy.iso: Puppy English customized ISO image.

Notes:

|Be sure to turn off the anti-virus software during the writing process, otherwise it will be unpleasant if it is intercepted. . . . The software comes from official sources and is non-toxic and harmless, so you can use it with confidence.

|If the startup is unsuccessful, find the "isolinux.cfg" file in the USB flash drive and change "pmedia=cd" in this file to "pmedia=usbflash".

|When writing with PuppyLiveUSB, it is recommended to set the USB boot mode to HDD.

After reading “Solution to Installing Linux System on USB Disk”, I also want to read:

1. How to install linux system using hard disk

2. How to install linux system using hard disk

3. How to install Linux system using USB disk

4. How to install Linux system to hard disk

The above is the detailed content of How to use Unetbootin to write the Linux system to a USB flash drive and perform boot settings. For more information, please follow other related articles on the PHP Chinese website!