My laptop cannot turn on after replacing the memory module

The notebook cannot be turned on after replacing the memory module

1. This situation is generally caused by dust problems, motherboard incompatibility, or poor contact. After the dust accumulates too much, when the weather changes, such as when it is relatively humid, the dust is prone to leakage, which may cause the computer to work unstable or even crash. Otherwise, it will burn out the hardware of the machine.

2. The memory module is not installed properly: Check whether the memory module is firmly inserted into the slot. If it is not installed properly, the computer will not start. It is recommended to disassemble and install again. Incompatible memory module: The specifications of the memory module do not meet the requirements of the computer, such as capacity, frequency, etc., which may cause the computer to fail to boot.

3. First, there is a problem with the plug. Second, the memory is incompatible. Third, the memory connection is not good and the contact is poor.

4. If the computer cannot be turned on after replacing the memory, it means that the memory module may be incompatible with the computer. Contact the memory dealer to determine whether the memory of the same model cannot be turned on after replacing the memory. The main reasons are as follows: 1. The original memory is useless and all the memory is used. If the new memory cannot be turned on, it may be an incompatibility problem, that is, the computer is old and the memory module is new, but the computer does not recognize it.

5. Your situation may be caused by the fact that you did not insert the new memory stick tightly when you inserted it. When you insert the memory stick into the slot at an angle, press it in hard, and then press it down again. stuck. You should have no compression issues.

Asus Notebook cannot be booted after installing additional memory. Why

1. Remove the installed hardware and then boot. If it can boot normally, the hardware compatibility may be poor. You can replace the hardware and add it. Give it a try. If the BIOS interface still cannot be displayed after booting, it is recommended to go to the service center for testing.

2. It may be a memory failure or memory incompatibility. 2. You can try to remove the original 2G memory, try using only a single 4G memory, and install it in a memory slot below. 3. If it still doesn’t work. It may be a memory failure or memory incompatibility. 4. The memory supported by A40J is up to 2G per stick and two slots, totaling 4G.

3. This problem may be caused by static electricity on the motherboard. For this situation, follow the steps below. (1) Please plug and unplug the adapter. (2) After connecting the power adapter, press and hold the power button for 12 seconds to do EC reset (the charging light goes off first and then on). (3) After that, press the power button to turn on the computer.

4. If the laptop cannot be turned on (cannot be turned on without turning it on), the problem may be caused by static electricity on the motherboard. For this situation, follow the steps below. (1) Please plug and unplug the adapter and battery.

5. Wrong memory is added. This notebook supports DDR3L 1600 MHz memory, 1x SO-DIMM slot (maximum support 8GB) system memory can be expanded up to 12 GB memory (operating system support required).

What to do if the computer cannot boot after inserting memory

Some motherboards are like this. If too many memory modules are inserted, problems will occur, causing the computer to fail to start and other problems. If this is the case, you can consider going to a merchant to replace the motherboard. In addition, in view of the situation at the beginning of the article, Master Lu recommends that you take your computer to the merchant for a physical examination.

You can remove the COMS battery from the motherboard, cut off the power, wait a few minutes and then install it. Sometimes the COMS configuration changes due to hardware changes, which may also cause the computer to fail to boot. If none of these work, consider it. Motherboard or cpu problem.

If there is a dust problem, remove the dust first, especially in memory slots that have been empty for a long time. There may be dust, causing poor contact of the memory modules. Compatibility issues. If the old article can work normally, it means there is no problem.

If the computer cannot be turned on after replacing the memory, it means that the memory module may be incompatible with the computer. Contact the memory dealer to determine whether the memory of the same model cannot be turned on after replacing the memory. The main reasons are as follows: 1. The original memory is useless, and all the new memory is used. , it cannot be turned on, it is probably an incompatibility problem, that is, the computer is old and the memory module is new, and the computer does not recognize it.

The computer can be turned on by inserting one memory stick, but cannot be turned on by inserting two. Since the motherboard has two memory slots, it must be reasonable and can be used normally. As you said: two memories and two slots can be used independently, but they cannot be used at the same time. This situation usually occurs due to power supply problems.

If two pieces of memory can be turned on individually but cannot be turned on together, it means there is a serious compatibility problem. If neither memory can boot, it may be that the memory is bad or the computer is broken. Can be determined by substitution method. Memory is one of the important components in a computer. It is the bridge between external memory and the CPU.

The above is the detailed content of My laptop cannot turn on after replacing the memory module. For more information, please follow other related articles on the PHP Chinese website!