php Editor Xigua, recently found a question in the community about the burnout of the DC motor connected to the motherboard. This situation may be caused by a problem caused by overpowering the motor or incorrect wiring. In order to avoid this from happening, we need to carefully check factors such as motor specifications, wiring methods, and motherboard load capacity to ensure that the requirements are met and connected correctly to ensure the normal operation of the equipment and extend its service life.
1. Check whether the motor is forced to stop during operation. At the moment of forced stop, the current is up to several times the normal operating current.
2. The driving power of the speed regulator is smaller than that of the DC motor, and the drive tube will be burned during startup or forced stop. Replace the large power drive block to solve the problem.
3. The H-bridge of the speed regulator is not connected to the protection diode, causing the new self-induced electromotive force to break down the H-bridge MOS tube when it stops.
4. It is recommended to add a fuse before the drive bridge. Prevent the governor from burning out.
5. The PWM control circuit is of poor quality.
Therefore, when using a DC motor speed regulator, you should always check the above five points to avoid problems with the DC motor speed regulator.
If there is no screwdriver or screwdriver bit on the main board of your range hood, you can use a Phillips screwdriver, a pair of pliers or a piece of thin wire to replace it. The specific method is as follows:
Disassemble the main board of the range hood, use a Phillips screwdriver to unscrew the screws, and take out the old main board of the range hood
Under normal circumstances, the maintenance cost of the main board and motor of a fully automatic washing machine is relatively high. If the motherboard is broken and needs to be replaced, a motherboard will cost 300 yuan. If the motor is burned out, it will be more expensive to replace the motor. Might as well get a new one.
This situation may be caused by the brake power-off switch being damaged. When this happens, it is recommended to replace the brake power-off switch. In addition, there are other possible reasons:
1. The motor wire is loose or burnt;
2. The battery power is low, or the battery wiring is loose and connected somewhere, or there may be The battery is broken;
3. The handle has poor contact;
4. The fixing nut of the motor is loose, just tighten it;
5. The controller is faulty. The motor Hall is faulty, the motor is burned, and the motor bearings are broken.
First check whether the motor nut is tightened, whether the battery power is sufficient, and whether the tire pressure is sufficient. If you have tools, you can dismantle the seat to see if the battery cable is disconnected, if the screws are loose, and if the controller connection wire is burnt or loose.
The 3D printer can accurately print the model by dragging the tray and the movement of the nozzle, without missing any parts. The motor provides power for the movement of the nozzle, the tray and the z-axis. The quality of the motor is directly Affects the performance of 3D printers.
Except for the cooling fan, the 3D printer has 4 main motors, namely the X-axis, Y-axis, Z-axis and nozzle. The motor is responsible for movement and positioning in the 3-axis, so the quality of the motor is directly related to the printing quality. . The motor of the nozzle is responsible for controlling the extraction and ejection of raw materials. If the quality of the motor is slightly poor, it will cause the nozzle to eject too much or too little raw material, which directly determines the printing result. Based on the importance of motors, 3D printers on the market all use special high-performance motors for superior printing quality. Both lifespan and control performance are not comparable to ordinary motors.
Special motors bring high performance but also have some disadvantages. First of all, the price is much more expensive than ordinary motors, and then there is the trouble of maintenance. Once the motor of the user's 3D printer is damaged, it cannot be replaced by itself. , there is no other way but to contact after-sales service, which brings inconvenience to maintenance.
If the garage flap door does not work properly, you can first determine whether the main board or the motor is damaged by the following methods: Check the power supply: If there is no problem with the power supply, then the motor itself may be faulty. You can check whether the motor power contact is good, whether the motor shows signs of burnt or damaged, and whether the circuit board has solder joint problems or damage. Check the indicator light: If the indicator light is on, you can basically judge that the transformer is good, and the problem may lie in the motherboard or motor. If the light does not light up, there may be a problem with the motherboard or motor. Check the buttons: If the door does not respond when you press the buttons on the mainboard or case, the mainboard or motor is broken. If the door can move but cannot stop when you press a button on the motherboard or case, it means the motherboard is broken. The above methods are for reference only. If you still have questions, it is recommended to consult professional technicians for more in-depth inspection and diagnosis.
It's absolutely fine. If you know electricity, just turn off the computer board, directly connect the maximum airflow and lights, and just unplug and plug in the power plug.
The reasons why Mitsubishi air conditioner burns the motherboard are as follows:
1. The main reason is unstable voltage and excessive current.
2. The fault causes the system to start frequently and overloads the motherboard.
3. The motherboard components are aging.
4. The humidity is too high or water enters, causing a short circuit on the motherboard.
5. Animal conductors such as mice cause the motherboard to short-circuit.
There are two fuses on the air conditioner circuit board, one for weak current and one for strong current. The varistor will only burn out when the voltage is too high, or there will be a short circuit or leakage. The voltage When the lower current is too large, the power circuit of the air conditioner circuit board is damaged, the temperature sensor of the circuit board is damaged, and the receiving circuit of the air conditioner circuit board is damaged. These are all possible reasons for the air conditioner circuit board to burn out.
The main board on the Weili 12428 motor cannot be removed. Weili 12428 is an electric off-road climbing remote control vehicle. The main board on the motor is the core component of vehicle control, responsible for receiving remote control signals, controlling motor operation and other functions. If the main board is removed from the motor, the vehicle will not operate properly. Therefore, it is not recommended to remove the main board from the motor. If you have any questions about the vehicle's performance or other aspects, it is recommended to consult professional technicians or the manufacturer for answers.
The above is the detailed content of Will the motherboard burn if it is connected to a DC motor?. For more information, please follow other related articles on the PHP Chinese website!
![[Web front-end] Node.js quick start](https://img.php.cn/upload/course/000/000/067/662b5d34ba7c0227.png)
