How to find the 12v interface on the computer motherboard?

php Editor The 12V interface on the strawberry computer motherboard is to provide power to various components inside the computer. To find this interface, you first need to check the motherboard's user manual or find the motherboard's specifications. Typically, this connector is located in a rectangular slot on the motherboard, and may be labeled 12V, PWR, CPU_PWR, or something similar. In addition, the 12V interface is usually a 4-pin or 8-pin socket that corresponds to the power cable. By carefully observing the logo and slot shape on the motherboard, you can accurately find the 12V interface and connect the power cord. If you are still unsure, it is recommended to consult the motherboard manufacturer or seek professional help.

How to find the 12v interface on the computer motherboard?

This socket is usually near the CPU fan power supply slot. It is a socket very close to the CPU. This was originally used as an auxiliary power supply for the CPU, but now it is used as an independent power supply slot for the CPU. But it is not available on some boards, because the CPU power supply of such boards is directly integrated on the motherboard. In other words, the power supply from the chassis is directly connected to the motherboard power supply interface with the 24-pin pin.

Can the number of pins on the power supply and motherboard be different?

.

.

Now the mainboard power interface is a 24pin interface, and the new power supply is also a 24pin interface, so there is no mismatch problem.

The old power supply has a 20pin socket, but it can be plugged into a 24pin socket and is compatible.

Generally, desktop power supplies have four types of plugs. What are the four types?

First of all, you need to understand the various working voltage lines of the computer's power supply. The computer's working voltage wires, that is to say, the wires connected from the power supply, include ±5V (red), ±12V (yellow), signal wires (gray), and black is the ground wire. Therefore, the general interfaces of computer power supply are:

1. IDE device D-type interface, using 12V voltage 2. USB interface using 5V voltage 3. S-ATA power interface, using 12V voltage 4. 3.5-inch floppy disk Driver power interface (this interface is basically canceled at present) According to the above interface types, you can convert the same voltage to each other. In addition, the sockets where the power supply connects to the motherboard and supplies power to the motherboard must also be distinguished. There are two main types. Since it has little to do with your question, I won’t elaborate further.

Which one is plugged into motherboard power supply r or l?

Normally, the R and L sockets of the motherboard power supply correspond to the right channel and left channel respectively. This is because the motherboard power supply is typically used to connect audio devices such as speakers or headphones. Stereo sound can be achieved by plugging the right channel into the R jack and the left channel into the L jack. Ensuring proper insertion ensures proper transmission of the audio signal and balanced sound. If plugged in backwards, the sound may be unbalanced or only have a mono output. So make sure to plug R into the right channel jack and L into the left channel jack for the best audio experience.

Which host power cord needs to be plugged into the motherboard?

There are three lines. Plug in the power supply, host and motherboard respectively.

The power cord from the power supply is plugged into the motherboard, hard disk and graphics card respectively (most low-end graphics cards do not need it);

The data cable that connects the motherboard to the hard disk and optical drive, the old one is IDE interface cable, SATA cable is commonly used now;

The indicator light cable and data cable from the chassis to the motherboard, including the power switch (Power), restart (Reboot), hard disk light, and power light on the chassis, Front panel USB interface cable and audio output cable.

How many pins does the power connector on the computer motherboard have?

The old power supply is a 20-pin power supply, and the power of a 20-pin power supply is generally not very large. Most 24-pin motherboards cannot use a 20-pin power supply. Some motherboards can make do, but due to insufficient power supply of the motherboard, it may cause excessive power supply. question.

If you must insert it, look for the side where the bayonet is facing the tenon (if it is reversed, it cannot be inserted), face the side where the bayonet is facing the tenon, and then insert the 20-pin into the 20-pin on the left side of the 24-pin. needles (4 needles to the right of the empty one). The extra 4 pins are for additional power supply of 12V and 5V. Although you can buy an adapter cable, which is the big four-pin old hard drive power socket, and convert it into the 20-pin socket with the missing 4 pins, the total power of the power supply is dead. Generally, old power supplies are 250~300W, while dual-core CPU motherboards require at least 300W, or even more than 400W power supplies. Therefore, it is not recommended to use a 20-pin power supply on a 24-pin motherboard.

What is the hard drive power interface on the motherboard?

It is the common D-type interface on computer power supplies. It has four wires, red, yellow and black, that can provide two voltages, 12 volts and 5 volts at the same time. There are usually several such power interfaces on a computer power supply.

cpu power supply interface socket?

1. Things that need to be plugged in, especially current CPUs, have higher power supply requirements than before. Even if a few do not connect to this power supply, they can still work normally. That is because the current CPU has not reached its limit state. They are all dual-core, or even higher. The previous power supply may have insufficient power supply. The expanded 4-pin is to deal with insufficient power supply. Therefore, in order to ensure the stable operation of the CPU, this interface must be connected.

2. Generally, the CPU power supply interface on the motherboard has four ports, and there is no need to plug in eight ports. If your CPU is very energy-consuming (such as new, quad-core, eight-core, etc.) you may also consider plugging it in.

3. Some power supplies provide 8pin (4pin*2) power supply, but the CPU power supply on the motherboard only has a 4pin interface. Then you only need to disassemble the 8pin and turn it into two 4pins to use. 4. Some motherboards have an 8-pin CPU power supply design, but the power supply only has a 4-pin interface. As long as it is plugged into the four ports on the left of the 8-pin, the shape can only match the left 4 pins, as long as it provides 12V voltage.

The above is the detailed content of How to find the 12v interface on the computer motherboard?. For more information, please follow other related articles on the PHP Chinese website!