1. Solution: Try to recheck the connection between the computer and the network cable. If there is a fault, you can find a professional for repair. . It may be that the wireless network has been accidentally disabled, causing the network connection to fail.
2. Operator issues. Many times, if the computer does not have a network, it may not be a computer problem, but a problem with the network itself. Therefore, you should first check whether network equipment such as routers are operating normally. If the computer cannot access the Internet, check other devices connected to the same network, such as other computers and mobile phones, to see if they can access the Internet.
3. What should I do if the desktop computer network is limited or has no connection? If you can’t access the Internet, just look for Internet problems.
4. First restart the router and optical modem, then check if you can access the Internet, re-plug and unplug the network cable, and check if the connection is normal. Repair via command. Start, search, enter cmd, right-click and run as administrator, then enter the following 2 commands to repair the network configuration and winsock protocol.
5. It will return to normal immediately after payment. When the network cable or router connected to the computer becomes loose, you will naturally be unable to access the Internet. This is also a very common phenomenon. Sometimes accidentally touching the network cable will cause the network cable to become loose. At this time, you only need to re-plug the network cable to strengthen the connection.
6. Solution 1 for a desktop computer that suddenly cannot access the Internet. First, recall whether you have touched the modem, network cable and telephone line, or whether you have recently gone to a telecommunications business hall to handle upgrades or modifications.
It’s a problem with the operator. Many times, if the computer does not have a network, it may not be a computer problem, but a problem with the network itself. Therefore, you should first check whether network equipment such as routers are operating normally. If the computer cannot access the Internet, check other devices connected to the same network, such as other computers and mobile phones, to see if they can access the Internet.
First restart the router and optical modem, and then check if you can access the Internet. Replug and unplug the network cable to check if the connection is normal. Repair via command. Start, search, enter cmd, right-click and run as administrator, then enter the following 2 commands to repair the network configuration and winsock protocol.
Here are the steps to troubleshoot your desktop computer's inability to connect to the wireless network: Check your network connection: Make sure the wireless network connection is turned on and your computer is connected to the correct network. Check the wireless adapter: Make sure the wireless adapter on your computer is enabled.
If networking is disabled on your desktop computer, you may not be able to connect to the Internet or other networks. This could be due to various reasons such as network setup issues, network administrator configuration issues, or malware infection. Here are some ways to fix this problem: Check network settings: Make sure your computer's network settings are correct.
. Many times, if the computer does not have a network, it may not be a computer problem, but a problem with the network itself. Therefore, you should first check whether network equipment such as routers are operating normally. If the computer cannot access the Internet, check other devices connected to the same network, such as other computers and mobile phones, to see if they can access the Internet.
First restart the router and optical modem, and then check if you can access the Internet. Replug and unplug the network cable to check if the connection is normal. Repair via command. Start, search, enter cmd, right-click and run as administrator, then enter the following 2 commands to repair the network configuration and winsock protocol.
Check the network connection: Make sure the wireless network connection is turned on and your computer is connected to the correct network. Check the wireless adapter: Make sure the wireless adapter on your computer is enabled. You can enable it by pressing "Fn" on your keyboard and the wireless adapter icon.
Desktop computer cannot connect to the Internet. Solution: Operating device: Lenovo y570. Device system: win7. Operating software: computer desktop. The reason may be caused by incorrect IP address and gateway of the computer or DNS failure. As shown in the picture, the computer cannot connect to the Internet.
Cause 1: The network cable is faulty (plug in the network cable on the computer or the network cable between the router and the cat). Solution: Make the crystal head again. After it is done, you can use a network cable tester to test it. If the 6 lights are on, it means the production is successful, or you can replace the network cable to solve the problem. Reason two: The network card driver is not installed or the driver is abnormal.
Usually, the reasons why a desktop computer has a normal network connection but cannot access the Internet: DHCP is not enabled on the router, the IP cannot be obtained, the network is restricted, or someone on the same network is using an executive, causing interference.
Network settings error. It may be because the set network parameters, gateway address, subnet mask, DNS server, etc. are entered incorrectly. In order to solve this problem, you need to perform the following steps: Check whether the network cable connection is correct and whether the network cable port is loose or corroded.
The broadband cannot be connected due to system damage. Solution: Install or restore the system. The broadband equipment is damaged, causing the network connection to fail. Solution: Find a professional for inspection and repair, and replace it with a new broadband if necessary. A virus in the computer causes the computer to be unable to connect to the Internet.
Cause 1: Network cable failure (plug in the network cable on the computer or the network cable between the router and the cat) Solution: Make the crystal head again. After it is done, you can use the network cable tester to test it. If the 6 light is on, it means it is made. Success, or replace the network cable to solve the problem. Reason two: The network card driver is not installed or the driver is abnormal.
There are many reasons why a desktop computer cannot access the Internet after plugging in the network cable. The network card problem is that if the network card is not plugged in properly, it will be useless if the network cable is plugged in, so plug the network card again.
The desktop computer cannot access the Internet after plugging in the network cable. The reason is that there is a problem with the network cable itself, or the wireless network at home itself cannot connect to the Internet, and the desktop DNS needs to be repaired, or the network card driver is abnormal. Needs to be fixed.
1. Computer system configuration problems: (1) Reset the network: Press WIN R on the desktop, enter CMD, and click OK to open the command prompt window, win10 Press win
2. First restart the router and optical modem, and then check whether you can access the Internet. Replug and unplug the network cable to check whether the connection is normal. Repair via command. Start, search, enter cmd, right-click and run as administrator, then enter the following 2 commands to repair the network configuration and winsock protocol.
3. The reason why the desktop computer has no network: Check whether the router light is normal. If it is a light modem, generally the other lights are on except the LOS light. You can turn off the power of the router and modem, and then turn them back on after 5 minutes.
4. The reason why the desktop computer is connected but cannot access the Internet is as follows: operator problem. Many times, if the computer does not have a network, it may not be a computer problem, but a problem with the network itself. Therefore, you should first check whether network equipment such as routers are operating normally.
5. Solution for desktop computer not connecting to the Internet: Operating device: Lenovo y570. Device system: win7. Operating software: computer desktop. The reason may be caused by incorrect IP address and gateway of the computer or DNS failure. As shown in the picture, the computer cannot connect to the Internet.
The above is the detailed content of Desktop computer without network. For more information, please follow other related articles on the PHP Chinese website!
win10 bluetooth switch is missing
Why do all the icons in the lower right corner of win10 show up?
The difference between win10 sleep and hibernation
Win10 pauses updates
What to do if the Bluetooth switch is missing in Windows 10
win10 connect to shared printer
Clean up junk in win10
How to share printer in win10
![[Web front-end] Node.js quick start](https://img.php.cn/upload/course/000/000/067/662b5d34ba7c0227.png)
