When assembling a cabinet, it is inevitable to remove the screws. Faced with various types of screws, how to choose the right tool? PHP editor Strawberry has compiled a tool guide for removing screws, including the characteristics of different types of screws, applicable tools and detailed operating methods. Read on to learn how to easily and efficiently remove screws from assembled cabinets.
When assembling a cabinet, you usually need to use the following tools for disassembly:
1. Screwdriver: A screwdriver is one of the most basic tools. You may need a flat-blade screwdriver or a Phillips screwdriver, depending on the type of screws you are using.
2. Wrench: Wrench is usually used to adjust the tightness of nuts or bolts. Depending on your needs, you may need different size wrenches.
3. Hammer: A hammer can be used to tap the spliced parts of the cabinet to loosen them.
4. Iron Saw: If the cabinet parts require cutting to remove, you may need to use an iron saw to do so.
5. Scissors: In some cases, you may need scissors to cut through plastic, rope, or other auxiliary materials.
6. Manual or electric screwdriver: If the screws are very tight or require frequent removal, it may be more convenient and efficient to use a manual or electric screwdriver.
Please note that the specific tools required to disassemble a cabinet may vary depending on the cabinet type, material, and construction. Before dismantling, it is recommended to check the cabinet's assembly instructions or refer to relevant guides for the correct steps and tools required to ensure safe and efficient disassembly.
The tools required to assemble a computer are roughly as follows:
Screwdriver: flat-angle screwdriver and Phillips screwdriver
Pliers: Install copper pillars Use
Tweezers: used for working in small spaces (connecting jumpers)
Parts box: used to place various disassembled small parts
Cable ties: used to bind various power cords and data cables in the chassis
Network cable pliers: used to connect crystal connectors
Thermal silicone: used when installing the CPU
Multimeter: used to measure voltage and current
Dust removal brush: clean the dust in the chassis
Finger cots: Place the components inside the chassis that are damaged by static electricity on your body
Power socket: This alternative
Processor: Intel Core i5-10400F (chip) ￥959; Radiator: Cooler Master Blizzard T400i ￥89; Graphics card GALAXY RTX 2060 6G Snapdragon (boxed) ￥2299; Motherboard: ASUS TUF B460M PLUS Gaming motherboard ￥719; memory: Kingston Hacker DDR4 2666 8G*2 (dual channel memory) ￥239+239.
Hard drive: Western Digital SN550 500GB NVMe protocol M.2 solid-state drive ￥469; Chassis: Patriot Shadow 2 ￥219; Power supply: Antec BP500 (rated 500W) ￥269; Monitor: user selected; Keyboard and mouse: user’s choice.
1.
Turn on the computer, right-click on the desktop to open a shortcut menu;
2.
Click the small icon in the shortcut menu Tools;
3.
Open the gadget that comes with the computer;
4.
Click on the calendar;
5.
The calendar gadget you just opened appears in the upper right corner of the desktop;
6.
Find and double-click the clock;
7.
The clock will appear in the upper right corner of the screen, which is very convenient.
Fishing rod assembly: This is simple, just install the wheel on the fishing rod and tighten it. It is best to thread the wire along the wire hole, which is convenient for use. How to use the explosive hook: first thread the lead pendant onto the line, fix both ends with space beans, and then tie the explosive hook to the rear end of the thread. Put the bait on when using it, tighten the line after casting from a long distance, fix the fishing rod to the shore with a bracket, and then clip the bell.
The answer is as follows: 1. Knife: used to cut parts and remove burrs from parts. It is recommended to use a professional craft knife or scissors.
2. Pliers: used to clamp parts, tighten screws and bend parts. Slender nose forceps and flat forceps are recommended.
3. Wrench: used to tighten screws and nuts. It is recommended to use a variety of wrenches to accommodate different screws and nuts.
4. Screwdriver: used to tighten screws. It is recommended to use screwdrivers of different specifications and types to adapt to different screw types.
5. Sharpener: used to remove burrs on parts and cut small parts. It is recommended to use a professional craft sharpener.
6. Drilling machine: used for drilling holes and processing parts. It is recommended to use electric drills with different sizes of drill bits and attachments.
7. Curve pliers: used to bend and adjust parts. It is recommended to use slim curved pliers.
8. Glue stick: used for gluing and bonding parts. It is recommended to use a professional glue applicator stick.
9. Steel ruler: used to measure part size and spacing. It is recommended to use a high-precision steel ruler.
10. Flashlight: Used to illuminate the work area to see parts and tools more clearly. It is recommended to use a handheld portable flashlight.
Assembling the power part of the watch
If you want to assemble a watch, you must first understand the structural relationship and working principles between the various parts of the watch and start with the original system. When we turn the handle by hand and tighten the coil, the watch generates power. This power drives the gear train to rotate, and rotates through the gear to the speed control part of the escapement, and then controls the speed through this part, and finally drives the time pointer to indicate the time. This is a working relationship between them. Among them, the rewinding handle can not only play the role of rewinding, but also move the pointer in time.
Assembling the external parts of the watch The components and working principle of a mechanical watch are composed of external parts and a center. Appearance parts, dials, hands and other directly visible parts
Assembling the central components of the watch
Central components: main transmission gear train, escapement speed control system, pointer transmission gear train, upward Winding needle extraction mechanism, etc. These components are composed of upper, middle and lower layers of plywood. The lower plywood is the main plywood and basic component. Soil plywood includes strip plywood, swing plate and cross plate. The middle layer must be composed of mountain plywood and fork plywood.
When assembling the watch, we should pay attention to some points. I believe it is not difficult for you who love watches. However, when the watch is assembled and everything looks fine, the most troublesome problem arises.
Importance of experience in assembling watches
If you find that your watch is not on time, you should start to check the problem and eliminate it. This involves not only technical issues, but more importantly experience. Therefore, you cannot enumerate narratives and visualizations of pictures. Therefore, you should invite interested friends to "understand" yourself, and also ask some questions and troubleshooting methods that affect the accuracy of the operation. Maybe it can relieve many of your doubts.
Assembly Watch Test
To understand that the watch is not accurate, the best way is to test it with a professional tester. The general test is to perform 9 times in the three directions of up, down, and up at 3 o'clock without rolling up, partially rolling up, or fully rolling up. The average value of all data is used as a reference for judgment (the upper left corner of the data is the "daily error value", +10/-10; the middle is the "center value", +5/-5; the right side is the "swing range".
Due to different frequencies, such as vibration, there are different settings. The frequency is 28800 times/hour, the amplitude is above 270, the data on the lower right is "frequency", and the other numbers on the screen do not need to be repeated here. If it should be smooth, wavy or tilted, it indicates that there is a problem with the watch and needs to be further understood and eliminated.
You can use a blower can or vacuum cleaner to clean the computer fan. Because computer fans will accumulate dust after long-term use, resulting in poor heat dissipation and affecting the performance and life of the computer. Use a blower can to blow away the dust on the fan, and use a vacuum cleaner to suck away the dust. Both methods are effective. Clean the computer fan. In addition, you need to pay attention to safety when cleaning the computer fan to avoid damage to the computer or injury.
1. On the computer. Color generally uses PS software, that is, PhotoShop software, which is the most commonly used image processing software; there is also FLASH software; professional computer coloring should use professional color separation software such as Jinchang Software. This kind of software is more expensive but has complete functions. It is color separation software.
2. PS software is graphic design software. The current version is generally CS6 or above. Any flat effect can be produced through this software; FLASH is animation production software, which is divided into three-dimensional and two-dimensional. In the two major areas of dimensionality, FLASH animation and animation in QQ space are basically the effects produced by this software. This software has different versions. For animation production, you can download the FLASHCS4 version, which is relatively new and has quite complete tools. When making animations, Photoshop software is also involved, using it to process some pictures or correct animation character effects.
What tools can be used to clean computer fans? A small brush, vacuum cleaner or compressed air can and other tools can clean the dust on the surface of the computer radiator and fan blades. The vacuum cleaner can suck away the dust, and the compressed air can can remove the dust inside the fan. Blow away the dust. It is recommended to turn off the power before using any tools and disassemble the computer for cleaning. At the same time, in order to ensure the cleaning effect, it should be cleaned regularly to avoid dust accumulation affecting the cooling effect of the fan, causing the computer to heat up, crash, etc. Problem occurs.
The above is the detailed content of What tools are used to assemble and dismantle cabinets?. For more information, please follow other related articles on the PHP Chinese website!
![[Web front-end] Node.js quick start](https://img.php.cn/upload/course/000/000/067/662b5d34ba7c0227.png)
