Detailed explanation of the air-conditioning assembly line work. The air-conditioning assembly line is a job that requires patience and meticulousness. It involves using various tools and machines to assemble and test air conditioning components. This job requires both physical strength and concentration. This job may be suitable for those who like to work with their hands and pay attention to details. In this article, php editor Banana will delve into all aspects of air-conditioning assembly line work, including responsibilities, skill requirements, work environment, and career prospects.
It’s not easy to do.
I once did it at Gree Air Conditioning Electronics Factory. I also did it at Midea Air Conditioning Electronics Factory. Including Haier Refrigerator Factory, etc. Working on an assembly line is definitely a busy job, and your hand speed must be fast otherwise you won't be able to keep up with others. It doesn't have much technical content, and it's not difficult to learn, but it's quite tedious. After a long time, most people can’t stand it!
want. Generally, assembly lines have a large flow of people. There is no fixed number of people either. The recruitment volume is large
Chain assembly in shoe factory assembly lines is a complex process involving multiple steps and components. The following are the general assembly steps:
1. Prepare tools and materials: Make sure you have all the tools you need, such as screwdrivers, wrenches, chain links, sprockets, chain tensioners, etc. Additionally, make sure you have the correct chain model and specifications to match your assembly line equipment.
2. Check the existing chain: Before starting assembly, check the existing chain for wear, damage, or looseness. If you notice problems, you may need to replace the chain.
3. Install the sprockets: Install the sprockets on the shaft of the assembly line, making sure they are properly aligned and fixed in place. Use a wrench to tighten the bolts on the sprocket.
4. Measure and cut the chain: According to the length of the assembly line and the spacing of the sprockets, measure the required chain length. Use a chain cutter to cut the chain to the desired length.
5. Connect the chain: Connect the two ends of the chain together to form a ring. This usually involves inserting a special connecting piece, such as a link pin or quick coupler, into the end of the chain. Make sure the connection is tight and the chain is running smoothly.
6. Install the chain tensioner: Install the chain tensioner according to the manufacturer's recommendations. A chain tensioner helps maintain the correct tension on your chain, preventing it from loosening or skipping teeth.
7. Adjust the chain tension: Use the chain tensioner to adjust the chain tension to ensure that the chain runs smoothly on the sprocket and is not loose or overtight.
8. Inspection and Testing: After completing the assembly, check whether the chain is correctly installed on the sprocket and make sure the chain runs smoothly. Carry out a test run and observe the chain for any unusual noise, vibration or overheating.
Please note that the specific assembly steps may vary due to different shoe factory assembly lines and chain types. Therefore, before beginning assembly, be sure to carefully read the equipment's operating manual and service guide to ensure correct and safe operation. If necessary, please contact a professional service technician for assistance.
In the Aidi Precision Motor factory workshop, the robotic arm is on the assembly line, and the robot automated processing line is the first in the industry to realize unmanned automatic processing.
They are all assembly lines, step by step, install one piece or several pieces at a time
1. Clean the socket bottom box. The socket is installed after carpenters and painters, etc., and the bottom box that has been left for a long time will inevitably accumulate a lot of dust. During installation, first clean the bottom box of the switch socket, especially the dust and impurities in the box, and wipe away the remaining dust in the box with a damp cloth. This can prevent special impurities from affecting the use of the circuit.
2. Power cord handling. Leave the wires thrown out of the box for maintenance length, and then cut out the wire core, being careful not to damage the wire core. Wind the wire clockwise around the terminal corresponding to the switch or socket, and then tighten the indenter so that the core of the wire must not be exposed.
3. Three-wire socket wiring method. Connect the live wire to the A mark in one of the two holes of the switch, then take out the insulated wire from the other hole and connect it to the L hole in the three holes of the socket below. The neutral wire is directly connected to the N hole among the three holes of the socket and connected firmly. The ground wire is directly connected to the E hole among the three holes of the socket and connected firmly. If the neutral wire and the ground wire are incorrectly connected, tripping may occur when using electrical appliances.
4. Fixed installation of sockets. First, pass the wires thrown out of the box through the outlet holes of the plastic table, and then fasten the plastic table to the wall and fix it on the box with screws. After fixing, pass the wires through the wire holes of the switch socket according to their respective positions, and press the wires firmly according to the wiring requirements. Finally, attach the switch or socket to the plastic table, align it and fix it firmly with screws, and cover it with a decorative plate.
very tired.
Working on the assembly line, everyone is fixed at a position and repeats the same actions every day. I feel like a robot. The only difference from a robot is that I can speak...
When I first started working, I worked in a factory on the assembly line for a year. I remember very well that the factory was making electronic scales. It was very large and there were many employees. There were more than a dozen assembly lines in one workshop. There were thirty or forty people, and everyone was working hard with their heads down. It was very uncomfortable on the first day when I went to work. I looked at the assembly line that was always conveying, and I had to work quickly on the assembly line
Generally speaking, it is not very tiring to assemble the car rearview mirror water line. Compared with the small line assembly in electronics factories, it takes less effort. But you must be familiar with and understand the skills of your work at work!
Not tired. The refrigerator factory assembly line is not tiring. Just click it into the component's slot. Just follow the work standards. It's just that the assembly line work is a little boring. The same kind of work is repeated every day. If you yearn for freedom, you may not be suitable for this job. Because the body is not tired at work. But I feel physically and mentally tired for a long time. Is the mobile phone factory assembled on an assembly line or on a piece-by-piece basis?
The above is the detailed content of Is it easy to build an air conditioner assembly line?. For more information, please follow other related articles on the PHP Chinese website!
![[Web front-end] Node.js quick start](https://img.php.cn/upload/course/000/000/067/662b5d34ba7c0227.png)
