How to install a computer assembly line? How to plug in computer headphones? How to plug in computer headphones?

With the development of computer technology, many people have begun to assemble their own computers. However, during the assembly process, various problems may be encountered. PHP editor Baicao has received many questions about the installation of computer assembly lines and computer headphones. In order to help you solve these problems, the editor has specially compiled detailed answers, hoping to help you successfully assemble your own computer.

How to install a computer assembly line?

1. Plug the power supply next to the missing pin

2. Plug the power supply opposite to reset

3. Plug the power light next to the power supply, and the negative pole is close to the power jumper

4. Plug the hard disk light next to reset, the negative pole close to the reset jumper, and the power supply next to the missing pin. How to plug in computer headphones? How to plug in computer headphones?

1. First look at the plug of the headset. The pink one is the microphone plug with a microphone pattern on it. The black one (sometimes green) is the sound output plug, with a headphone pattern painted on it.

2. Look at the sockets on the computer again. Headphones are usually plugged into the front of the chassis. There are two sockets on the front panel of the chassis, one red and one green. The pink one is the microphone socket and the green one is the audio output socket. Many chassis are also painted with patterns to show the distinction.

3. After understanding the headphone plug and the chassis socket, you just need to plug them in one by one. It doesn't matter if they are plugged in backwards, just swap them over.

4. There are also sockets on the back of the chassis, but there are at least three, and some have two rows of six. No matter how many there are, just remember that the pink one is the microphone jack and the green one is the audio output jack. Don't worry about anything else. Some baffles also have graphic logos.

How to insert the computer pin?

Pins on the motherboard

1. Power switch (POWER)

The plug of this switch has two pins. In order to facilitate user identification, one of the wires is normally connected It is represented by yellow or black, while the other connection is usually white. This plug must be plugged in, otherwise the computer cannot be started through the chassis panel. In addition, it can also be started by directly shorting the POWER pin on the motherboard. The connecting plug of this switch is generally marked with POWER SW, and the English abbreviation near the corresponding pin on the motherboard is generally PWR, Power SW, PWR SW, PW, PW SW or PS, etc.

2. Reset switch (RESET)

The plug of the reset switch is also two-pin. One of the connections is generally indicated by blue, and the other connection is white. Its function is to restart the computer without power interruption, and is often used when the computer suddenly crashes while it is running. The plug connected to this switch is usually marked RESET SW, and the English abbreviations near the corresponding pins on the motherboard are generally RESET, RST, RS or RE, etc.

3. Power LED (POWER LED)

The power light connection is also a two-pin plug. One connection is generally indicated by green, and the other connection is white. When the host power is turned on, the power light will light up. The plug connected to this switch is usually marked with POWER LED, and the English abbreviations near the corresponding pins on the motherboard are generally PW LED, Power LED, PWR LED or PLED+ and PLED-, etc.

4. Hard drive light (HDD LED)

The hard drive light connection is also a two-pin plug. The two connections are usually one red and one white. When the hard disk is reading or writing, the hard disk light will light up. The plug connected to this switch is usually marked with HDD LED, and the English abbreviations near the corresponding pins on the motherboard are generally HDD LED, HD or IDE_LED+ and IDE_LDE-, etc.

5.Speaker

The plug of this connection has four pins, but there are only two connections. The color is usually one red and one black or one orange and one black. After being connected correctly, it can be used by the speakers on the chassis. The plug connected to this switch and the corresponding pin on the motherboard are usually marked with the word "Speaker". Some computers will emit a "beep" sound through the speaker after starting normally, or they will emit a corresponding alarm sound through the speaker when they cannot start normally to help users solve problems. However, some motherboards already have integrated speakers, so there is no need to connect the speakers on the chassis.

How to move the Spielt assembly line?

Regarding this issue, Sputtering System (Sputtering System) is usually larger and heavier, so moving requires certain methods and tools.

Generally speaking, moving the Spielt assembly line requires the use of tools such as mobile trucks, forklifts or trolleys. The specific steps are as follows:

1. First, you need to determine the moving route to ensure that the route is unobstructed.

2. Disassemble all components on the Spielt assembly line and place them in corresponding boxes or containers to avoid damage.

3. Move tools such as dolly trucks, forklifts or hand trucks next to the Spilt assembly line in preparation for moving it.

4. Place the main body of the Spielt assembly line on a mobile truck, forklift or trolley, and secure it to avoid shaking and damage during movement.

5. Place all components of the Spielt assembly line in the corresponding boxes or containers and secure them to avoid loosening and damage during movement.

6. Slowly push tools such as mobile trucks, forklifts or trolleys onto the Spilt assembly line, making sure to move smoothly and avoid collisions and falls.

7. After moving the Spielt assembly line to its destination, reassemble and debug it to ensure its normal operation.

It should be noted that moving the Spielt assembly line requires great care and caution to avoid damage or safety accidents during the move. If you're not familiar with moving a Spilt assembly line, it's best to call a professional to do it.

How to assemble the line set for Panyu?

Pan fishing is a common way of fishing. The following is the general line assembly method for pan fishing:

Connect the main line to the fishing rod and connect the float to the main line. The float is usually attached to the main line using an eye loop on the top of the rod or a knot tied around the rod.

Add a fish float between the main line and the hook to control the float depth. Tie a small fishing float to the main line, usually 5 to 15 cm below the float, so that the depth of the float can be adjusted as needed.

Attach the fishhook to the main line. Tie a small knot at the end of the main line, then thread the hook's loop through the knot and pull tight.

Add bait below the hook. Put an appropriate amount of bait on the hook, and you can choose different bait types and quantities according to the preferences of different fish and local fishing skills. Adjust the float depth. Move the float up or down along the main line until you find the depth where the fish are.

The above is the detailed content of How to install a computer assembly line? How to plug in computer headphones? How to plug in computer headphones?. For more information, please follow other related articles on the PHP Chinese website!