How to solve the problem of HP part number appearing on HP h1005?

php editor Zimo will answer your questions about the HP part number on the HP h1005 printer. When your printer displays an HP part number, it usually means that a part is faulty or needs to be replaced. A solution to this problem can be to check if the parts of the printer are installed correctly and if they need to be cleaned or replaced. Alternatively, you can try restarting the printer or updating the printer driver. If the problem persists, it is recommended that you contact HP official customer service or repair center for further help and support.

How to solve the problem of hp part number on HP h1005?

It should be scannererror20. The scan head needs to be cleaned or is broken. When such a situation occurs and the HPM1005scannererror20 error message appears that generally cannot scan or copy, the following steps are usually used:

1. After removing the glass panel cover, remove the right control panel. There is a screw under the plastic panel with the model printed on it. You can find the depression by touching it and use a screwdriver to remove the screw;

2. Remove the screws on the glass panel and flip the scanning assembly over. You can see a series of white gears, motors and black spiral shafts.

3. Normally, engineers first wipe the black spiral shaft and white gear, adjust the pressing piece on the white gear, and finally check whether all cables are plugged in. After completing the above steps, install all components and turn on the computer.

If the hp1005scannererror20 prompt continues to appear, you can try to completely remove the pressing piece on the white gear.

Generally, the fault of HP printer can be solved. If the fault still cannot be solved, it may be necessary to replace the scan head with a new one. (It is also possible to replace the scanning cable)

Introduction to repairing the hp1005 power board?

Introduction to hp1005 power board repair

Introduction to power circuit board repair, it is divided into two parts: the front stage and the front stage. The front stage first checks and transforms the mains power, then rectifies and filters to output pure DC. Check whether the voltage is normal. The subsequent stage processes the DC voltage, such as oscillation amplification, etc., and then detects whether the pulse or signal output required for industrial control is suitable.

What kind of toner cartridge is hp1005?

hp1005 toner cartridge model:

HP 1005 is a black and white laser multi-function machine that prints, copies, and scans, and is suitable for 2612A toner cartridges.

HP HP12A toner cartridge: full name HP Q2612A. Mainly used in printers and all-in-one machines, such as HP's 1020 and 1005. HP12A toner cartridge color is black.

The toner cartridge is the core of the printer, and the quality of printing depends entirely on the toner cartridge.

hp1005 printer does not require help to add toner

Tools/Materials

Modification tools A wallpaper knife and a pair of needle-nose pliers

hp1005 universal toner A bottle

Rubber gloves (according to your own situation)

Method/step

First take out the toner cartridge from the printer, on the left side of the printer toner cartridge (the orientation when the toner cartridge is placed in the printer) There is a black cover that is connected to the printer toner cartridge shell. We need to cut it off because there is an inlet for adding powder. Pay attention to safety when cutting the cover and do not damage other parts of the toner cartridge.

After cutting off the black shell, remove the translucent plastic cover, carefully add toner, and be careful not to bring debris into the toner cartridge.

Finally, close the cover, lay the toner cartridge flat, empty it and shake it left and right to make the toner evenly distributed in the toner cartridge. Install the toner cartridge into the printer and start printing. In this way, you have successfully added toner to the printer!

How to install HP m1005 paper roll?

The HP M1005 paper roll installation process is as follows: 1. Turn on the printer power switch and ensure that the printer is in normal operation. 2. Open the paper roller cover and notice that there is a paper sensor inside the paper roller. You need to place the paper on the sensor. 3. Place the paper on the sensor, making sure the paper lies flat and does not get caught in the winder. 4. Press the roll start button, and the motor inside the roll starts to work, rolling the paper into the roll. 5. After the paper is rolled into the paper roller, you can judge whether the paper roller needs to be cleaned by observing the number of papers in the printer. 6. When it is time to clean the paper roller, open the paper roller cover, take out the paper inside the paper roller, and then close the paper roller cover. 7. Turn off the printer power switch and disconnect the printer power. The above is the installation process of HP M1005 paper roll wheel. Follow the steps to ensure the normal operation of the paper roll and avoid failures caused by improper operation.

How about HP M1005?

The performance is also very powerful. First of all, the preheating time of this printer can be said to be 0 seconds, which is almost ignored. In terms of processor, it can reach 230MHz, and the corresponding memory size is 32MB. For the double-sided function, it needs to be done manually.

HP M1005 displays ERROR: B0601 error when it is turned on?

None of the above mentioned are on point, and some repair stations falsely reported that the motherboard was broken. In fact, download the firmware from the official website, install it through the connection, and it will be fine after initialization.

How to solve the problem that HP1005 is in initializingi state and cannot be ready?

The machine cannot enter the system, and the motherboard failure is very likely.

The above is the detailed content of How to solve the problem of HP part number appearing on HP h1005?. For more information, please follow other related articles on the PHP Chinese website!