The computer motherboard battery is one of the important components in the computer. It is responsible for saving the computer's time, date, BIOS settings and other information. As the use time increases, the motherboard battery may become low in power or fail and need to be replaced. So, how to replace the computer motherboard battery? In this article, PHP editor Youzi will introduce in detail the steps and precautions for replacing the motherboard battery, helping you successfully complete the battery replacement and ensure the normal operation of the computer.
Steps to replace the computer motherboard battery:
The first step is, near the south bridge of the motherboard, there is a silver-white disc button battery with a plus sign on the back and about two centimeters in diameter.
The second step is to use a flat tool to press the latch on the CMOS battery holder.
The third step is to pop up the battery on the motherboard automatically and then take it out by hand.
Installing the battery: Place the side without the buckle first, then place the battery flat on the slot, press it with the side, and there will be a click. The battery replacement is completed.
1. First buy a new motherboard BIOS battery. Make sure it is the same number as the battery on your computer. It is usually 2032. Go to the computer store to buy one with the same model
2. Turn off the power of the computer, open the case cover, and you will see a round battery. The battery is very bright and easy to find. The diameter is about 1.5-2.0CM. Take out the battery. There are batteries for each motherboard. The seats are different, so the battery removal methods are also different. Generally, they are divided into three types: external button type, top pressure type, and top button type. Take out the battery carefully!
3. At this time, take out the battery you bought Take out the new battery, be careful not to mistake the positive and negative directions of the battery (there are signs on the battery), press it, it is installed, and then close the chassis cover.
You don’t need to change the battery when replacing the motherboard. The power of the motherboard battery can keep the motherboard bios running for five to eight years. Generally speaking, the motherboard bios consumes very little power. A button battery can keep it running for five to eight years. 8 years, so there is no need to replace the battery when replacing the motherboard. This battery has a relatively long running time. When certain parameters remain unchanged, the battery needs to be replaced.
Generally, the motherboard battery uses a button battery. You must first disassemble the motherboard and see the model of the motherboard battery. According to this model, purchase and install the battery product. You can easily replace the button battery. If there is a problem with the motherboard battery Generally, the time is not accurate, so it is very necessary to replace the motherboard battery. You must see the battery model clearly before replacing it. I hope my answer can help you.
Step/Method 1
First shut down the computer and cut off all relevant power sources to the computer.
Step/Method 2
Open the case and look for the battery (be sure to use metal to eliminate static electricity when touching parts of the case to prevent injury).
Step/Method 3
The battery is not difficult to find. You will see a coin-sized thing on the motherboard, which is the battery.
Step/Method 4
First remove the battery. After observation, you can see that there will be a small clip next to the battery. Use a screwdriver to push it and the battery will pop out (if If there are no small clips, use a screwdriver and gently pry it open).
Step/Method 5
After taking it off, you can install the prepared new battery. Just put it in according to the position of the original battery, but be careful not to Even if the installation is backwards, don't make it very loose.
The following are the general steps for replacing the computer motherboard battery:
1. First, you need to determine the correct battery model and specifications. The battery model number is usually written on the battery, and information can also be found in the motherboard manual. Most motherboards use CR2032 type batteries.
2. Shut down the computer and remove power. Remove the power cord and make sure the static electricity is gone. You can also press the power button for a few seconds to release any stored charge on the motherboard.
3. Open the computer case. Usually some front panels, side panels or top cover need to be removed.
4. Locate the battery location. The battery is usually located on the edge near the motherboard, such as next to the PCI slot, SATA port, etc.
5. Use a wide-headed flat-head screwdriver or small flat-nose pliers to lift the circlip or retaining clip of the battery and remove the battery. Be careful not to forcefully remove or twist the battery.
6. Insert the new battery into the slot. Correct insertion direction is important, usually right side up.
7. Press the circlip or retaining clip against the battery to ensure that the battery is stable.
8. Close the computer case, plug in the power, and start the computer.
After that, you may need to reset some options in the BIOS setup menu, such as date, time, boot sequence, etc. If you are not familiar with BIOS settings, please refer to the motherboard manual or contact the manufacturer or after-sales service for support.
1. First of all, the motherboard is inside the host computer. Some people who don’t understand even think that the motherboard is inside the monitor, except for all-in-one computers. We open the back cover of the chassis. There are usually two screws on the back. The computer cover can be removed by unscrewing it, as shown in the picture.
2. Be sure to cut off the power before taking out the battery. It is best to leave the host in operation for a day to avoid electric shock.
3. Then in the host computer, you can see a large circuit board. This circuit board is the motherboard, and the battery is on it, as shown in the picture.
4. Then we need to remove the battery. We don’t need any tools. It can be removed with one hand. No hard board is required, as shown in the picture.
5. We press the pressing piece from the inside and outward, and the battery will pop out, but not enough. At this time, the card can no longer catch the battery, as shown in the picture.
6. Then we press down slightly on the edge of the battery opposite the card, and the battery can be tilted up. We can take out the battery, as shown in the picture.
7. Then you can see the battery slot, which is a metal piece. When installing, be sure to keep the positive terminal of the battery facing the metal piece, as shown in the picture.
8. We can see that the side without text is the positive terminal of the battery. Be sure to keep an eye on it, as shown in the picture.
9. There is text on the side and the battery model. We need to prepare a battery of the same model, as shown in the picture.
10. When we install the battery, first put the edge of the battery opposite the side card, then square the battery, and press down slightly on the metal piece to install the battery. If you press with too much force and the battery cannot enter, you can press the metal card outward to allow the battery to enter, as shown in the picture.
The above is the detailed content of How to replace the computer motherboard battery?. For more information, please follow other related articles on the PHP Chinese website!
![[Web front-end] Node.js quick start](https://img.php.cn/upload/course/000/000/067/662b5d34ba7c0227.png)
