How to partition a disk using parted

When encountering brokenendopes problems, you can follow the following steps to solve them: 1. Use sudoapt--fix-brokeninstall or try to install after cleaning; 2. Check and correct software source configuration errors; 3. Manually install, uninstall or reinstall conflict packages; 4. Clean the cache or reinstall related components. In most cases, these methods can be used to fix dependency problems without excessive worry.

Toremoveapackageusingyum,usethecommandsudoyumremovepackage_name,whichremovesthepackageandpotentiallyitsunuseddependencies.Beforedoingso,ensureyouhavethecorrectpackagenamewithyumlistorrpm-q,checkdependenciesviayumdeplist,andavoidremovingcriticalsystem

To view the system log, you need to select the corresponding tool according to the operating system. Windows uses event viewer, with the path to Win R, enter eventvwr.msc, to view the "System" classification under "Windows Log", and supports filtering and saving; Linux system logs are usually located in /var/log/ directory, such as syslog, messages, dmesg files, and can be viewed by tail-f or journalctl-u service name commands; Mac can view logs through the Console application or logshow command. When viewing, you should pay attention to error and warning level information, analyze problems based on timestamps and context, and pay attention to permission requirements.

To create and use a network namespace, you need to create it first, then assign the interface and IP, and set up the routing to achieve communication. The steps are as follows: 1. Create a namespace with ipnetnsadd; 2. Create a vethpair through iplinkadd and move one end into the namespace; 3. Assign IP to the interface and enable it; 4. If you need external network access, enable IP forwarding, configure iptablesMASQUERADE and set default routes; 5. Close the interface first and clean the rules when deleting. The entire process needs to pay attention to resource cleaning and rule consistency.

netstat is a practical tool for troubleshooting network problems and checking connection status. Common uses include: 1. Use netstat-a to view all active connections, filter TCP for -t, and UDP for -u; 2. Display program name and service name plus -n parameters to improve speed; 3. Use netstat-l to view the listening port, combined with -tulnp to display process information; 4. Find programs that occupy a specific port can be implemented through grep: port number and ps command; 5. If the system is not installed, try the ss command or install the net-tools package, and the root permissions are required to execute the -p parameter to obtain the complete information.

The key to using parted partition disks is to master several steps: 1. Preparation: Confirm the target disk device name (such as /dev/sdb) and judge its partition table type. If it is less than 2TB, use MSDOS (MBR) and if it is greater than 2TB, use GPT; 2. Create a partition table: After entering parted operation mode, execute the mklabel command to select gpt or msdos, this step will clear the disk data; 3. Start partition: Use the mkpart command to specify the partition type, file system and start and end location, such as mkpartprimaryext40GB50GB, and continue to add other partitions; 4. Format and mount the partition: manually execute mkfs.ext4 and other commands to format,

To ensure that the system time synchronization is reliable, first make sure that the NTP service is installed and run, use systemctl to check the state of ntp or chronyd, and start and set up the power-on self-start if necessary. Secondly, configure a suitable NTP server, modify the /etc/ntp.conf or /etc/chrony/chrony.conf file, and recommend choosing a server with a similar geographical location such as Alibaba Cloud or Tencent Cloud. Finally, check the synchronization status and use ntpq-p or chronycsources to view the connection status. If the offset is too large, you can use ntpdate to manually calibrate it, but long-term synchronization should rely on background services to ensure stability.

When a file is occupied, you can search and end the occupied process by the following methods: 1. The Windows system can use the task manager to search for file handles with the resource monitor; 2. Use the handle.exe tool of Sysinternals to query accurately, requiring administrator permission; 3. Linux/macOS uses the lsof command to search for keywords, and grep can search for keywords; 4. Before ending the process, you must confirm the purpose. Windows can use the task manager or taskkill command, and Linux/macOS can use the kill command to avoid killing the system process by mistake.