Example comparison of how PHP reads large files efficiently

Reading large files has always been a headache. If we use PHP to develop and read small files, we can directly use various functions to achieve it. However, once we get to a large article, we will find that the commonly used methods cannot be used normally or take too long. It's too stuck. Let's take a look at the solution to the problem of reading large files in PHP. I hope it will be helpful to everyone.

In PHP, when reading files, the fastest way is to use some functions such as file and file_get_contents. It can be completed beautifully with just a few lines of code. The functionality we need. But when the file being operated is a relatively large file, these functions may be insufficient. The following will start with a requirement to explain the commonly used operating methods for reading large files.

Requirements:
There is an 800M log file with approximately more than 5 million lines. Use PHP to return the contents of the last few lines.

Implementation method:

1. Directly use the file function to operate
Since the file function reads all the contents into the memory at one time, PHP in order to prevent some poorly written programs Occupying too much memory will cause insufficient system memory and cause the server to crash. Therefore, by default, the maximum memory usage is limited to 16M. This is set through memory_limit = 16M in php.ini. If this value is set to -1 , the memory usage is unlimited.

The following is a piece of code that uses file to extract the last line of this file:

The entire code execution takes 116.9613 (s).
My machine has 2 G of memory. When I press F5 to run, the system turns gray and recovers after almost 20 minutes. It can be seen that the consequences of reading such a large file directly into the memory are serious, so As a last resort, memory_limit cannot be set too high, otherwise you will have to call the computer room to reset the machine.

2. Directly call the Linux tail command to display the last few lines
Under the Linux command line, you can directly use tail -n 10 access.log to easily display the last few lines of the log file. You can directly Use PHP to call the tail command and execute the PHP code as follows:

The entire code execution takes 0.0034 (s)

3. Directly use PHP’s fseek to perform file operations
This This method is the most common method. It does not need to read all the contents of the file, but operates directly through pointers, so the efficiency is quite efficient. When using fseek to operate files, there are many different methods, and the efficiency may be slightly different. The following are two commonly used methods:

Method 1
First find the file through fseek The last EOF, then find the starting position of the last row, get the data of this row, then find the starting position of the next row, then take the position of this row, and so on, until the $num row is found.
The implementation code is as follows

 0) { while ($t != "＼n") { fseek($fp, $pos, SEEK_END); $t = fgetc($fp); $pos--; } $t = " "; $data .= fgets($fp); $line--; } fclose($fp); echo $data ?>

It takes 0.0095 (s) to complete the execution of the entire code

Method 2
Still use fseek to read from the end of the file, but this time it is not the same Read bit by bit, but read piece by piece. Every time a piece of data is read, the read data is placed in a buf, and then the number of newline characters (＼n) is used to determine whether the last piece of data has been read. $num rows of data.
The implementation code is as follows

 $chunk) ? $chunk : $max - $len; fseek($fp, ($len + $seekSize) * -1, SEEK_END); $readData = fread($fp, $seekSize) . $readData; if (substr_count($readData, "＼n") >= $num + 1) { preg_match("!(.*?＼n){" . ($num) . "}$!", $readData, $match); $data = $match[0]; break; } } fclose($fp); echo $data; ?>

The entire code execution takes 0.0009(s).

Method 3

 0); $pos = $n + 1; $lines = array(); while (count($lines) <= $n) { try { fseek($fp, -$pos, SEEK_END); } catch (Exception $e) { fseek(0); break; } $pos *= $base; while (!feof($fp)) { array_unshift($lines, fgets($fp)); } } return array_slice($lines, 0, $n); } var_dump(tail(fopen("access.log", "r+"), 10)); ?>

The entire code execution takes 0.0003(s)

Method 4, PHP’s stream_get_line function, reads quickly, and reads 500,000 pieces of data file, it will take about 20 seconds! The example code is as follows

$fp = fopen('./iis.log', 'r'); //文件 while (!feof($fp)) { //for($j=1;$j<=1000;$j++) { //读取下面的1000行并存储到数组中 $logarray[] = stream_get_line($fp, 65535, "＼n"); // break; // } }

Related recommendations:

php Detailed explanation of file reading series methods

PHP file reading fread, fgets, fgetc, file_get_contents and file function usage example code

##A brief introduction to PHP file lock and process lock

The above is the detailed content of Example comparison of how PHP reads large files efficiently. For more information, please follow other related articles on the PHP Chinese website!