Reinstalling the system is the fastest way to solve the problem. If the computer is stuck in the Windows startup interface, it means that the computer system has failed, the system cannot boot, or the graphics card driver does not match.
After the computer starts, before entering the "Starting Windows" interface, press Ctrl Alt Del to automatically restart the computer and run the Windows system normally.
Solution: Disconnect all external devices to see if you can enter the system normally. If so, it means there should be no problem with the hard disk. Meaning: Starting the Windows system. If you stay too long, you will get stuck on the "Windows is starting" interface.
Make sure that the problem of being stuck in the Windows startup interface is not a system problem. If it is, you will not be able to enter safe mode. Even after reinstalling the system, it is still stuck in this interface. I still can't enter the Windows PE operating system using a USB flash drive, which means it's definitely not a problem with the computer system.
Solution to the problem that the Windows interface is stuck when the computer is booting: Click the F8 button to see if you can enter safe mode. If you can enter, just click Repair. If F8 does not work, you need to reinstall the system. If it can run after reinstalling the system, it can be opened normally.
1. Shut down the computer first, then open the main case, unplug the power cord and data cable of the hard disk, and then plug them in again after 2 minutes. Try restarting the computer.
2. Restart the computer: Sometimes simply restarting the computer can solve the problem. Enter Safe Mode: You can try entering Safe Mode and try to fix the problem. To enter Safe Mode, press the F8 key at startup and select Safe Mode.
3. If it cannot be started, it is very likely that the system is damaged, which can be solved by reinstalling the system. You can follow the steps below to install the system disk: Put the system CD into the CD-ROM drive. Turn on the power, and then observe the screen prompts. Before starting the system, press "F2" to set up the BIOS. Set the startup mode.
4. First, check the software fault and try to repair it. The computer cannot start normally because Caused by software failure. ...This type of failure is divided into two types: system software failure and application software failure. ...We can find the fault point through troubleshooting and try to solve it through software repair.
Please shut down and disconnect the power supply of the laptop, and then press and hold the power button of the computer to discharge and reset the motherboard; press it again after resetting. If the problem persists, it is suspected that there is a problem with the computer hardware. It is recommended that you take the computer and go to the local Lenovo service station for repair. Install the system to solve the problem. Follow the steps below to install the system disk: Put the system CD into the CD-ROM drive. Turn on the power, then observe the screen prompts, and press "F2" to set up the BIOS before starting the system. Set the startup method.
Shut down the computer, then press the computer’s power button, and then the computer will display the “Lenovo” logo, as shown in the picture below. When you see the "Lenovo" logo, immediately press the "F8" key on your computer keyboard to enter the Windows advanced menu option mode, as shown in the figure below.
The Windows failed to start error may be caused by problems such as system file corruption, hardware failure, or missing boot files. Here are possible solutions: Try booting into Windows Safe Mode and see if you can get into the system and fix the problem. If possible, you can use System Restore to restore your system to a previous state.
There are two solutions. The first method is to shut down the computer and then restart it. At the same time, press and hold the F8 key on your keyboard to enter the advanced startup options. After entering Advanced Startup Options, select Perform Last Known Good Configuration from your Advanced Startup Options.
What should I do if my Lenovo computer cannot enter the system?
2. It may be that the startup disk is set incorrectly. It is recommended to set the startup disk to a CD, floppy disk, or U disk, etc. Check whether the hard disk contact is not good and whether the hard disk mode setting is wrong. Check whether there is an optical drive, USB flash drive, floppy disk, etc., and remove it if there is one.
3. Unplug all peripherals, such as U disk, mobile hard disk, etc. Press F2 to enter BIOS after booting. Be sure to pay attention to the English on the boot page. At this time, you need to remember the keyboard button to enter the BIOS settings. In the example picture, it is the Enter key. Enter the BIOS setup window and select startup.
The solution to the problem that the computer cannot start Windows is as follows: System failure: Shut down the computer and then restart it. At the same time, press and hold the F8 key on the keyboard to enter the advanced startup options. , select Perform Last Known Good Configuration. Then press Enter. After the execution is completed, you can enter the system. Just reinstall the system.
Check internal and external computer cables If your computer has loose or damaged internal or external cables, it may not start. Try to check all internal and external cables to make sure they are plugged in correctly and not damaged.
Select "Last Known Good Configuration" on the Windows error recovery interface. If you can boot normally after that, it may be that a USB flash drive is plugged into the computer or the computer encountered a forced power outage last time. If the problem still cannot be solved through the first operation, it is recommended to shut down the computer and cut off the power supply.
When the computer cannot start Windows, we can try to enter safe mode to repair the system. Turn on the computer and press the F8 key continuously before the system enters the Windows startup screen. In the advanced boot menu interface that appears, select "Safe Mode".
You should press the F8 button before entering the operating system, then select the last known correct configuration, and then press the Enter key. You may consider reinstalling the system. Before reinstalling your system, make sure you have Windows installation media available (such as a DVD or USB flash drive) and a backup of all important data.
1. After thoroughly checking each drive letter, restart the computer to solve the problem. If it still doesn't work, continue reading.
2. Possible reasons why Lenovo laptop windows cannot start are: hardware incompatibility; software incompatibility; solution: it may cause failure to start. Friends who know technology can disassemble the machine and take a look. Users who do not understand It is recommended to take it to a professional repair shop for inspection or send it for warranty.
3. Restart the computer: Sometimes simply restarting the computer can solve the problem. Enter Safe Mode: You can try entering Safe Mode and try to fix the problem. To enter Safe Mode, press the F8 key at startup and select Safe Mode.
4. If it cannot be started, it is very likely that the system is damaged, which can be solved by reinstalling the system. You can follow the steps below to install the system disk: Put the system CD into the CD-ROM drive. Turn on the power, and then observe the screen prompts. Before starting the system, press "F2" to set up the BIOS. Set the startup method.
5. The default boot device missing appears when the Lenovo laptop is turned on. It means that the default boot device is missing or fails to start. , which means that the system cannot find the startup disk. Unplug all peripherals, restore the default BIOS settings and set the hard disk as the first startup item. The specific operations are as follows: Unplug all peripherals, such as USB flash drives, mobile hard disks, etc.
##
The above is the detailed content of Laptop cannot enter Windows system. For more information, please follow other related articles on the PHP Chinese website!
![[Web front-end] Node.js quick start](https://img.php.cn/upload/course/000/000/067/662b5d34ba7c0227.png)
