How to repair the mainboard of commercial 380v induction cooker?

php editor Baicao introduces you to the mainboard maintenance method of commercial 380V induction cooker. Induction cookers are common equipment in commercial kitchens. When the main board fails, normal use will be affected. When repairing, you first need to check whether the connection between the power line and the motherboard is good, and then use a multimeter to detect the motherboard components to find the fault point. Depending on the fault situation, repair measures such as welding and component replacement can be carried out. During the maintenance process, be sure to turn off the power and pay attention to safety, and ensure that the maintenance operations are correct to restore the normal working condition of the induction cooker.

How to repair the mainboard of commercial 380v induction cooker?

Commercial 380v induction cooker fault repair solutions are as follows: Common faults and repair methods of commercial induction cookers 1. Repair procedures for circuit board burned IGBT or fuse. If the current fuse or IGBT is burned, first confirm that the following parts are in a normal state. Replace, otherwise, the IGBT and fuse will burn out again.

1) Visually check whether the current fuse is blown; 2) Check whether the IGBT has broken down:

What should I do if the mainboard of the induction cooker is burned?

1. Do not rush to turn on the power after replacing the device. First, if possible, clean the copper surface of the circuit board with washing water. After drying, carefully observe the front and back of the circuit board. Make sure there are no continuous soldering, false soldering, or tin slag that may cause the machine to explode. In particular, check whether there are small metal wires on the back of the radiator and IGBT pins; check the circuits related to the fault. Check whether there are any broken or deteriorated components within the range. Confirm that there are no problems before turning on the power (note that it is powering on, not turning on the machine, and there is no load on the wiring board).

2. When powering on, you will hear a buzzer sound. If there is no sound, it means there is something wrong with the circuit board. Turn on the power and check the voltage of the power supply system, such as whether the rectifier bridge has a voltage of about 310V. Check whether the output, 5V, 12V, 18V (or 20V) voltages are normal, whether the voltage stabilizing device is hot, whether the driver stage output voltage is normal, and whether the levels of 339 or 393 are normal.

3. If the above checks are all normal, turn on the power button, and there should be a sound of looking for a pot. Then check the voltage of the relevant working point to see if it is normal. The driver-level pot-finding square wave signal and the pot-finding signal should jump once every 1 second when the buzzer sounds. If everything is normal, you can turn off the power, connect the load, and then turn on the power.

4. Since the main circuit operates at high voltage and high current when the induction cooker is working, the wire reel must be disconnected when checking the circuit. Otherwise, it is very easy to change due to the access of the instrument during the test. Incorrect circuit parameters cause burn-in.

5. When the current fuse or IGBT is burned out, the part cannot be replaced immediately. You must confirm that other related parts are in normal condition before replacement, otherwise the IGBT and fuse will burn out again.

Who knows the steps to repair the mainboard of induction cooker?

Although I cannot directly provide you with actual operations, I can tell you the general steps for repairing the mainboard of an induction cooker and what you need to pay attention to. Please be careful when repairing the mainboard of the induction cooker, as improper operation may cause damage to the induction cooker or cause safety hazards.

1. Preparation:

- Turn off the induction cooker, unplug the power supply, and ensure that the induction cooker is completely powered off.

- Prepare suitable screwdrivers and other repair tools.

- Ensure that the working environment is clean and tidy to avoid static electricity and dust from affecting maintenance.

2. Open the induction cooker:

- Remove the induction cooker shell, which may be a screw or snap-on design.

- After opening, you can see the internal structure of the induction cooker, including the mainboard, coils, fans, etc.

3. Detection problems:

- Observe whether the motherboard has obvious damage, such as burnt or broken circuits or components.

- Use a multimeter to check whether the motherboard's power supply, ground wires and key components (such as IGBT tubes, rectifier bridges, etc.) are normal.

4. Repair the motherboard:

- Take appropriate repair measures according to the problem. Such as replacing damaged components, re-soldering loose connections, etc.

- If the motherboard is severely damaged, the entire motherboard may need to be replaced.

5. Assembly and testing:

- After the repair is completed, return the induction cooker to its original condition, assemble and close the casing.

- Connect the power supply and turn on the induction cooker for testing to ensure that all functions are normal.

6. Safe operation:

- During the maintenance process, please be sure to pay attention to safe operation to prevent electric shock or damage to the induction cooker.

- If you encounter a problem that you are unsure about or cannot handle, please seek help from professional maintenance personnel.

Please note that the steps provided here are for reference only. Different models of induction cooktop motherboards may have different designs and repair methods. Before performing repairs, please check the specific model of the induction cooker and related repair information to ensure that the repair is completed safely and successfully.

How to repair a burnt silver wire on the mainboard of an induction cooker?

First, you need to cut off the power and open the furnace cover. Then use a pair of tweezers or pliers to grasp the broken silver wire end and solder it back to its original position. If needed, add some new silver wire to make sure the connection is strong. Finally, conduct a test to ensure that the induction cooker is functioning properly. If you are not familiar with repair techniques, it is recommended to find a professional repairman to repair it.

The above is the detailed content of How to repair the mainboard of commercial 380v induction cooker?. For more information, please follow other related articles on the PHP Chinese website!