Right click fails and cannot be operated

The right mouse button cannot be used

There are several solutions to this problem:

First try to replug and unplug the mouse, whether it is USB or PS/2 interface. If it is a USB interface, you can try to change it to an available USB port; if it is a PS/2 interface, you can check whether there is a problem with the pins (although it is less likely, because the right button is still available).

The method to uninstall the mouse driver is as follows: First press the key between CTRL and the window key on the keyboard to temporarily replace the right mouse button. Then follow these steps: On My Computer, right-click (on the keyboard) and select Properties, then Hardware, then Device Manager. In Device Manager, find Mouse and other pointing devices, then right-click the mouse (using the right button on the keyboard) and select Uninstall. In addition, you can also use the Start menu, select Settings, System, Hardware, Device Manager, then find the mouse and other pointing devices, right-click the mouse (use the right button of the keyboard), and select Uninstall. After the uninstallation is complete, re-plug and unplug the mouse, and the system will automatically install the mouse driver.

Try to use anti-virus software such as 360 and Kaspersky to eliminate problems caused by viruses and Trojans. If 360 cannot run, it may be a virus problem. You can try to start the computer in safe mode, then rename 360 ​​before performing anti-virus operations.

If your mouse isn't working properly, there could be a few reasons. First, check how your mouse is connected. If you are using the PS/2 interface, there may be a problem with the PS/2 interface on the motherboard, or the mouse itself may be faulty. If you are using a USB port, try connecting the mouse to a different USB port. If the problem persists, there is likely a problem with the mouse itself. You can try buying a new mouse to replace it. If you bought a new mouse and it still doesn't work properly, you can consider reinstalling the system. Sometimes, some system settings may cause the mouse to not work. Reinstalling the system can clear these problems and reset the system. Finally, if the problem still cannot be solved after the above steps, then it is likely that the motherboard has insufficient power supply. You can check whether the motherboard power supply is sufficient, try replacing the power supply or contact the manufacturer for repair. In short, if your rat

What to do if the right mouse button fails Cause analysis

Analysis of causes of right mouse button failure

1. It may be that the anti-virus software mistakenly deleted the shdoclc.dll file under windows/system32 on the C drive. You can first check whether there is still this file under system32

file, if not, then it must be causing trouble. You can download a shdoclc.dll file from the Internet. If it saves trouble, it is recommended to use 360

Security guard, click the system repair button

, this situation may be caused by the right mouse button failure caused by the response message of the right mouse button not being sent out in time. You can wait until the computer is idle or

You can try to optimize the computer system and try again to see if it can return to normal.

3. If the right mouse button fails while browsing the web, it is probably because the website has blocked the right mouse button. This may also cause the illusion that the right mouse button of others fails. 4: The system is busy and cannot respond

Your system has been installed for too long, or there are too many software installed, the registry is too large and there is too much garbage; or you have not done disk defragmentation for a long time; or you have installed multiple additional right-click menus

software; or the anti-virus software settings are too conservative. The solution can be to try to optimize the computer system.

5. If you use the mouse for a long time or pull it hard many times, one or more of the four wires in the mouse will break or have poor contact. This breakpoint is usually at the mouse

The front is not far, you can know it after a few experiments. Right-click and twist the wire, and move forward little by little. Of course, it depends on everyone’s usage habits. Changla

Or the folded place is easy to break. This is usually a mouse hardware failure. You can disassemble it yourself to see if there is any bad contact. It will usually be repaired.

Slow, use the chkdsk command. When clearing fragments, if you find files with many fragments, move them to other disks and then move them back after defragmentation. This is effective and fast

, the solution is generally to restart the computer and the fault will disappear.

7. It may be related to some services of the system, such as the file system, which causes system delays. Many friends like to increase the system speed as much as possible and disable it

This is caused by some mouse services. You need to check this yourself.

When encountering the above problems, we may need to find after-sales service. If it doesn't work, just change a mouse. Note that the service life of the mouse buttons is about 40,000 times, and even a worse mouse has a service life of 20,000 times. , if your mouse is not used for a long time, then the problem of right mouse button failure should be solvable

I can’t right-click on my computer

If the right mouse button cannot be used, please refer to the following steps to troubleshoot:

1. First, plug the mouse with a failed right-click into a different USB interface to check the hardware. Use the same method with the wireless mouse to try it first. If the problem still exists, then perform the following operations to solve the problem:

2. Use the key combination (win key r) to open the run window, enter "regedit" and press Enter to open the registry editor

3. Then expand the "HKEY_CURRENT_USERSoftwareMicrosoftWindowsCurrentVersionPoliciesExplorer" item in the registry editor window, find the "NoViewContexMenu" key value, and double-click the left mouse button.

4. In the pop-up window, change the numerical data to "0" and click the "OK" button.

It is also possible to directly delete the NoViewContexMenu key value. After completing the above operations, if the problem of being unable to use the right mouse button still exists, then please consider replacing the mouse.

The above is the detailed content of Right click fails and cannot be operated. For more information, please follow other related articles on the PHP Chinese website!